background image

1. TOP

1

14254

TOP MOUNTING SCREWS

2

SC-2425

2. REAR GLASS ASSEMBLY

1

14208

3. GRAPHICS PANEL

1

SG-23648

SIGN HOLDER

1

13098

MTG. SCREWS

4

SC-2425

4. GEAR MOTOR, 2.3 RPM W/CAPACITOR

1

MO-33383

MOTOR SHIM SPACER (

NOT SHOWN

)

4

MO-23651

SPLIT LOCK WASHER

4

WS-23671

#10 FLAT WASHER

4

WS-23672

5. SPROCKET WITH HUB

1

SO-23569

6. CHAIN NO. 25 — 40" (1016mm)

1

CH-23570

CHAIN LINK NO. 25

1

CH-23640

7. SPROCKET WITH HUB

1

SO-23569

INNER DRIVE BEARING ASSEMBLY

1

14860

DRIVE LUG & SHAFT (

NOT SHOWN

)

1

SO-23646

OUTER DRIVE BEARING ASSEMBLY

1

14859

8. CABLE CONNECTION HARDWARE

9. HEATING CABLE:  105' (32004mm)

1

CB-3045

10. INSULATION:  25" x 120" (635mm x 3048mm)

1

IN-22364

— BOARD INSULATION (

NOT SHOWN

)

CUT TO 3-1/2" X 7-1/2" (89mm X 191mm)

2

IN-2003

— BOARD INSULATION (

NOT SHOWN

)

CUT TO 3-1/2" X 9" (89mm X 229mm)

2

IN-2003

11. TEMPERED GLASS, SKYLIGHT

2

GL-23644

12. TERMINAL BLOCK ASSEMBLY

1

BK-33381

13. LAMP FIXTURE ASSEMBLY:

— LAMP FIXTURE

2

LP-33311

— LAMPS, 17 WATTS

2

LP-33341

— SHOULDER STUDS

4

ST-2547

14. FAN, 120V

1

FA-3599

FAN, 230V

1

FA-3568

FAN MOUNTING SCREWS

4

SC-2661

15. TEMPERATURE GAUGE

1

GU-3273

TEMPERATURE GAUGE WASHER

1

WS-22024

16. THERMOSTAT KNOB

1

KN-3473

THERMOSTAT 200 with # DIAL

1

TT-3057

THERMOSTAT WASHER

1

WS-22025

17. HEAT INDICATOR LIGHT, 120V

1

LI-3493

HEAT INDICATOR LIGHT, 230V

1

LI-3923

18. POWER SWITCH

2

SW-3409

19. PANEL OVERLAY

1

PE-23612

20.

MICROSWITCH

2

SW-33271

21. DOOR LATCH (MAGNETIC)

2

LT-23187

22. GLASS DOOR - LEFT HAND

1

4972

GLASS DOOR - RIGHT HAND

1

4973

EACH DOOR includes:

— DOOR HINGE, TOP

1

HG-2892

— DOOR HINGE, BOTTOM

1

HG-23952

— HINGE PIVOT PIN, TOP

1

PI-2894

— HINGE PIVOT PIN, BOTTOM

1

PI-23953

— HANDLE

1

HD-2910

— HANDLE MOUNTING SCREWS

2

SC-2911

— DOOR GASKET ASSEMBLY

1

GS-2891

23. SPINDLE ASSEMBLY:

— SPINDLE LUG ASSEMBLY

1

14211

— SLEEVE

10

SL-22578

— STUD / SIDE RACK

10

ST-22505

— S.S. 10-32X1/2" FLAT HEAD SCREWS

8

SC-23670

NOT IN ASSEMBLY:
SPINDLE BEARING (

NOT SHOWN

)

1

BG-23641

SPINDLE BEARING SCREWS (

NOT SHOWN

)

3

SC-2713

24. BASKETS, 24" (610mm)

10

BS-23645

25. DRIP PAN

1

PN-23166

26. RIGHT CASING ASSEMBLY

1

14217

27. LEFT CASING ASSEMBLY

1

14212

28. BOTTOM CASING ASSEMBLY

1

14523

MOUNTING SCREWS

6

SC-2425

29. POWER CORD:  12/3 CORDSET, 120V

1

CD-3397

POWER CORD, 230V

1

CD-3922

30. LEG OR CASTER BRACKET

2

4974

31. LEG OR CASTER BRACKET MOUNTING SCREWS 8

SC-2425

32.

BUMPER BREAKDOWN, PER UNIT  (

NOT SHOWN

) includes:

RAIL CHANNEL

2

13732

VINYL BUMPER, 3.4' (1036mm)

1

BM-24082

END CAP

4

BM-24083

MOUNTING SCREWS

10

SC-22425

33.

STACKING SPACER ASSEMBLY 

(OPTION) 

1

14209

includes:
STACKING FRAME

1

13102

ADHESIVE GASKET, 9.5' (2896mm)

1

GS-2019

# 8 2 9   O p e r a t i o n   &   C a r e   M a n u a l   •  

4.

HOT ROTATING VISUAL MERCHANDISER — 750-GDR

UNIT

ALTO-SHAAM

P A R T   D E S C R I P T I O N

QUANTITY

PART NO.

UNIT

ALTO-SHAAM

P A R T   D E S C R I P T I O N

QUANTITY

PART NO.

S E R V I C E   V I E W   O N   F O L L O W I N G   P A G E S

CABLE HEATING SERVICE KIT - Part No. 4879

Includes:

CB-3045

Cable Heating Element

112 ft.

CR-3226

Ring Connector

6

IN-3488

Insulation Corner

1 ft.

BU-3105

Shoulder Bushing

6

BU-3106

Cup Bushing

6

SL-3063

Insulating Sleeve

6

TA-3540

Electrical Tape

1 roll

12-21-00

Summary of Contents for 750-GDR










Reviews: