Alto-Shaam CombiTouch 7.14es Installation Manual Download

Page: 32 / 39

COMbIThERM® ES SERIES

•

ELECTRIC

INSTALLATION MANUAL #MN-28897 •

30.

i n s t a l l a t i o n

There is a remote possibility in the day-to-day operation of the Combitherm that the control could lock

or freeze. If this occurs, the control is easy to reset.

PRESS AND HOLD THE POWER KEY FOR A PERIOD OF 5 SECONDS.

Release the POWER KEY.

The control will will reset itself within approximately 15 seconds.

when reset, the disPlay will indicate the time and date and the controls will be Fully Functional.

CONTROL RESET

When the oven malfunctions, an error code will appear in the display.

PRESS THE START KEY TO ACKNOWLEDGE THE ERROR.

The keys that begin to flash represent operational modes that are still usable. Refer to Emergency

Operation.

When the oven fault is corrected, the Combitherm will return to normal Operation.

ERROR CODES AND REASONS

S E R v i C E m O D E A N D E R R O R C O D E S

Error

Code

Display Shows

When does the error occur?

Possible reason

E01

Low Water

ES units only:

• Activated if running in any mode and the

water level drops below the low level sensor.

• Activated if in standby mode and the water

level drops below the low level sensor for
3 minutes.

• Water supply is shut off.

• Low water pressure.

• Steam generator drain cap is off or loose.

• Drain pump is not sealing.

• Faulty or scaled water level probe.

• Faulty or plugged solenoid valve assembly.

• Wiring or connection issue.

E02

Control Temp High

Activated if the temperature of the electrical
control is higher than 176°F for 20 seconds.

• Cooling fan not operating.

• Unit is next to a heat producing source (there

is less than 20" clearance for the control side).

• Exhaust hood is not operating (if applicable).

E03

Fan Malfunction

Activated if the motor protection switch is
tripped.

• Motor rotation is backwards.

• Incorrect power to the unit.

• Connection problem at X-7 plug on relay

board pins 3-4.

E04

Aux Fan Fault

Auxiliary fan malfunction.

• Control setup programming error.

• Contact factory.

E11

Excess Oven Temp

Activated if the oven cavity temperature is
higher than 572°F for 25 seconds.

• Connection issue with oven temperature

sensor.

• Convection element contactor is stuck.

• Faulty oven temperature sensor.

Summary of Contents for CombiTouch 7.14es








































Search results

Summary of Contents for CombiTouch 7.14es

Reviews:

Related manuals for CombiTouch 7.14es

Brands by name

Popular brands

Alto-Shaam CombiTouch 7.14es, Installation Manual

Search results

Summary of Contents for CombiTouch 7.14es

Reviews:

Related manuals for CombiTouch 7.14es

Brands by name

Popular brands