background image

# 8 9 7 a •   I N S TA L L AT I O N / O P E R AT I O N / S E RV I C E   M A N U A L •  2.

SAFETY PROCEDURES
A N D   P R E C A U T I O N S

Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment.  In accordance with generally accepted
product safety labeling guidelines for potential
hazards, the following signal words and symbols
may be used throughout this manual.

Used to indicate the
presence of a hazard that

will

cause severe personal

injury, death, or substantial
property damage if the
warning included with this
symbol is ignored.

Used to indicate the
presence of a hazard that

can

cause personal injury,

possible death, or major
property damage if the
warning included with this
symbol is ignored.

Used to indicate the
presence of a hazard that
can or will cause minor or
moderate personal injury
or property damage if the
warning included with this
symbol is ignored.

Used to indicate the
presence of a hazard that
can or will cause minor
personal injury, property
damage, or a potential
unsafe practice if the
warning included with this
symbol is ignored.

Used to notify personnel of
installation, operation, or
maintenance information that is
important but not hazard related.

1.

This appliance is intended to cook, hold or
process foods for the purpose of human
consumption.  No other use for this
appliance is authorized or recommended.

2.

This appliance is intended for use in
commercial establishments where all
operators are familiar with the purpose,
limitations, and associated hazards of this
appliance.  Operating instructions and
warnings must be read and understood by 
all operators and users.

3.

Any troubleshooting guides, component
views, and parts lists included in this manual
are for general reference only and are intended
for use by qualified technical personnel.

4.

This manual should be considered a
permanent part of this appliance.  This
manual and all supplied instructions,
diagrams, schematics, parts lists, notices, and
labels must remain with the appliance if the
item is sold or moved to another location.

NOTE:

Summary of Contents for MM-30/2S
















Reviews: