background image

Form No. 78155B

10/01

AMERICAN SANDERS TECHNOLOGY

  

                                                         Printed in the U.S.A.

READ THIS BOOK

This book has important information for the use and safe operation of this machine.  Failure to read
this book prior to operating or attempting any service or maintenance procedure to your American
Sanders  Technology machine could result in injury to you or to other personnel; damage to the machine
or to other property could occur as well.  You must have training in the operation of this machine before
using it.  If you cannot read English, have this manual explained fully before attempting to operate this
machine.

Si  Ud. no pueden leer el Inglés, se hagan explicar este manual completamente antes de tratar el
manejo o servicio de esta máquina.

All directions given in this book are as seen from the operator’s position at the rear of the machine.

For new books write to:  ALTO U.S. INC.,  2100 Highway 265, Springdale,  Arkansas  72764.

Operator's

Manual

Super 7R

 Edger

IVIE Enterprises 

www.ivie-ent.com

    

Ph:(918)254-5161 or (888)262-5161   Fax:(918)250-4807 

Summary of Contents for 07011A









Reviews: