Alto MAXIDRIVE3.4 PC User Manual Download | Manualshive

Page: 14 / 22

background image

13

Outputs 1 ~ 6, RS485 OUT

GROUND

HOT (+)

COLD (

)

3

2

1

BALANCED XLR-F

8. APPLICATION

#

01

02

03

04

05

06

07

08

09

10

Name

DEFAULT

2X2W+MAX

2X3W

2X3W+MSB+MAX

4W+2MAX

4W+BSB+2MAX

5W+MAX

5W+BSB+MAX

6W

6W+BSB

Configuration

A135 B246

A13 B24 S56

A135 B246

A13 B24 S56

A1324 S56

A123 B4 S56

A12345 S6

A1234 B5 S6

A123456

A12345 B6

Configuration

Default preset - routing = 3-WAY STEREO

2-WAY 2 MONO FULL-RANGE OUT

3-WAY STEREO

3-WAY STEREO with MONO SUB + 1 MONO FULL-RANGE OUT

4-WAY MONO + 2 MONO FULL-RANGE OUT

4-WAY MONO with B-SUB + 2 MONO FULL-RANGE OUT

5-WAY MONO + 1 MONO FULL-RANGE OUT

5-WAY MONO with B-SUB + 1 MONO FULL-RANGE OUT

6-WAY MONO

6-WAY MONO with B-SUB

8.1 Factory Preset Configuration

The following diagrams show the MAXIDRIVE3.4 PC's various system configurations, as if to say, the various input
and output hardware combinations.

RS232

RS232 (9Pin-F)

PIN 5

PIN 3

PIN 2

(RXD) PIN3
(GND) PIN5

(TXD) PIN2

PIN 3(RXD)
PIN 2(TXD)
PIN 5(GND)

The wire must be changed between 2,3 pin.

9 PIN

9 PIN

Special attentions for R 232 interface:

S

1. Be careful not to use the pin-to-pin cable in the system, it may damage the communication part of this unit.
2. Be sure to use the female connector on both sides of the cable.
3. The length of this cable must not exceed 30 meters, or there would be some unexpected communication errors.
4. If you want to use a long distance remote control, it would be better to use shielding wire for this cable.

«
...
12
13
14
15
16
...
»

Summary of Contents for MAXIDRIVE3.4 PC























Reviews:

No comments

Related manuals for MAXIDRIVE3.4 PC

Brand: Blitz Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands