background image

8

4.5 Edit Mode (Password Protection)

Full Edit:

This is the DEFAULT mode. No password is set at the factory. From here you can lock the unit by clicking within
the empty

or

buttons. A text box will open, allowing you to enter a password of your own

Partial Lock

Total Lock

choice. Click

. It is important that you

.

OK

remember this password

Partial Lock:

In this mode, only the INPUT parameters may be edited. This is useful since it allows critical settings such as the
crossover points to be locked, while still allowing the user access to some overall EQ adjustment.

To enable

, a new password must be entered as above. To disable the lock, click within the empty

Partial Lock

Full

Edit

OK

button. A text box will open. Type the password that was used to set lock mode. Press

.

Total Lock:

No editing is possible in this mode. To enable

, a new password must be entered as above. To disable

Total Lock

the lock, follow the same instructions for disabling

.

Partial Lock

4.6 Help File

The

file accessible from within the PC Editor will be updated as necessary. Since software updates after the

HELP

printing of this manual may affect the instructions provided here, please check the Help File for any later remarks.

4.7 Introduction to the PC editor

When you launch the editor on your PC, you will see the opening screen following (later software versions may
differ). Each of the numbered sections is explained in the following pages - just look for the number icons within
the text.

Please note that a Windows compatible PC Editor is available for free download our web site.
To get a copy, go to http://www.proaudio.com.

1

2

3

4

5

6

7

Click on one of the icons on the PC editor, a window will appear showing one of several "pages" where you can
set the parameters using virtual knobs and sliders or by typing the values. Here is a brief overview of the various
functions that make up the MAXIDRIVE3.4 PC editor (community software). Each is explained in more detail in
the next section.

1

8

1

GAIN control section

This page presents 8 virtual slide controls, similar to what you would see on a professional sound mixing desk.
From here you can adjust the input/output

and output channel

and

.

LEVELS

MUTE

PHASE

MAXIDRIVE3.4 PC incorporates a password system and your installer may have set a password to ensure that
vital settings are not altered. In this case you will NOT be able to alter all of the parameters via the PC Editor.
In the PC Editor, select

and then the

tab. This will present you with a menu:

FILE > OPTIONS

LOCK

Summary of Contents for MAXIDRIVE3.4 PC























Reviews: