Diagnostics of the heater
The menu is only available when controlling digital types of heaters.
In standby mode (the display is off), press and hold the ">" button and
additionally press the button. The display will show "-Hd-", to enter the
diagnostics mode of the heater, press "P" in addition.
The display will show "FX:YY", where X is the number of the cell with the
error code, YY is the error code.
If there are no errors, YY takes the value "-".
To switch between the available cells with error codes, use the "<" and ">"
buttons. To delete all errors, press and hold the
button for 3 seconds.
If the Eberspacher heater is diagnosed, then pressing the "P" button will
move the current fault menu to the saved section from the menu and
display "EX:YY" with the same parameters.
To turn off the display, press "P" in addition.
Note:
description of error codes by the link https://altox.ru/en/docs/
Select heater type
In standby mode (the display is off), press and hold the "<" button and
additionally press ">". The display will show "H:XY", where X and Y are the
type of heater and digital protocol (default type is A0).
Set the required type of heater and digital protocol by pressing the "<" and
">" buttons, following the description:
Automatic/Analog
ue
:
A0 -
automatic detection of the digital type of heater
A1 -
heater with analogue signal control
Eberspacher:
Е1 - After Hydronic II
E2 -
F
actory-installed Hydronic II (Toyota, VW)
E3 -
F
actory-installed Hydronic II (Audi, Land Rover, VW)
E7 - Ventilation
(
Aftermarket
)
Webasto Thermo Top
:
t1 –
Thermo Top C/Z/V/EVO
/
VEVO
t2 –
Thermo Top V
/
VEVO
t3 –
Emulation
WTT
t4 –
Emulation
Timer
1533
t5 –
Emulation
Telestart (ver.1)
t6 – Emulation Telestart (ver.2)
t
7 – Ventilation (summer mode)
The selected type of heater is stored in memory after pressing "P".
Note:
automatic determination of the type Eberspacher and Webasto
digital heater (mode A0) occurs at the first start.
Display of time, voltage and temperature
The heater is started: To display the remaining operating time of the
heater, press the "<" or ">" button.
Then, to display the current time, press the "P" button.
The heater is stopped
:
To display the current time, press the "<" or ">"
button. In this section of the menu, pressing the "<" or ">" buttons will
display the seconds value of the current time.
Subsequent pressings of the "P" button switch to the voltage display
section, and then to the
car
parking heater temperature display section.
In the last section, to turn off the display, press the "P" button.
Примечание: The value of the
car
parking heater temperature is only
available on the part of the Eberspacher and Webasto digital heaters. If
the temperature value is not available, the menu section will be skipped.
Programming the timer
Three programmable timers are available to the user.
Each of the timers has two modes of operation:
— Single mode for switching on day ahead;
— Weekly mode of daily switching on for 7 days ahead.
Note: After 6 starts, the weekly mode automatically goes into single-turn
mode.
To view the status of the timer (activated or deactivated), in the standby
mode (the display is off), you must press the "P" button one, two or three
times, the display will show the timer number "-1t-"
"-2t-" or "-3t-", respectively.
The status of the timer is determined by the number of points in the right
corner:
— No points: the timer is deactivated
— One point: the timer is activated in the single-turn mode
— Two points: the timer is activated in a weekly mode
Activate / deactivate the timer and change the timer mode in the current
menu with the button.
To change the timer settings, press the "<" or ">" button, the display will
show the start time of the heater.
Press the "<", ">" and "P" buttons to set the desired start time of the heater,
then set the operating time of the heater "t:30" from 10 to 99 minutes.
After pressing "P", the settings will be saved and the timer will be
activated in the single-turn-on mode for the day ahead.
Note: in the timer "-1t-" setting menu, the stored operating time of the
heater "t:30" is the default start time from the direct-on button , and
from the external pulse signal at the INPUT input.
