background image

- 4 - 

ReServWPV

LED Diagnostics:

Power Supply Board

Red (DC)

Green (AC1)

Power Supply Status

ON

ON

Normal operating condition.

ON

OFF

Loss of AC. Stand-by battery supplying power.

OFF

ON

No DC output.

OFF

OFF

Loss of AC. Discharged or no stand-by battery. No Dc output.

ReServ Board

LED

LED State

Unit Status

Output LEDs

ON

------

Normal operating condition.

------

OFF Loss of 24VACand/or 12VDC output power.

Low Battery

ON

------

Stand-by batteries are low.

------

OFF Normal operating condition.

Shutdown

ON

------

Loss of 24VACand/or 12VDC output power. Discharged stand-by battery.

------

OFF Normal operating condition.

Audio Signal Diagnostics:

ReServ Unit

Audio Signal

Unit Status

Single Periodic Beep

AC Fail.

Double Periodic Beep Low Battery or No Battery.

Terminal Identification:

Power Supply Board

Terminal Legend Function/Description
L, G, N

Connect 220VAC 50Hz to these terminals: L to hot, N to neutral, G to ground.

--  DC +

24VDC non power-limited output. 

AC FAIL 

NO, C, NC

Form “C” dry contacts used to instantaneously signal the loss AC to local annunciation devices, 

with AC present terminals marked NO and C are open, NC and C are closed. When loss of AC

occurs, terminals marked NO and C are closed, NC and C are open.

BAT FAIL 

NO, C, NC

Form “C” dry contacts used to signal low battery voltage or loss of battery voltage. Under normal 

conditions terminals marked NO and C are open, NC and C are closed. During a trouble condition 

terminals marked NO and C are closed, and NC and C are open.

--  BAT +

Stand-by battery connections. Maximum charge current 0.7A.

ReServ Board

Terminal Legend

Function/Description

Input  ---  24VDC +

24VDC input from power supply board.

N, P 1-16

24VAC and/or 12VDC outputs. 

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the

presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient

magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important 

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION: To reduce the risk of electric shock do not open enclosure.

There are no user serviceable parts inside. Refer servicing to qualified

service personnel. 

Summary of Contents for ReServ1WPV









Reviews: