Altronix TROVE T3MK75F16V, Installation Manual

- 2 -  

T3MKV Kits

Overview:

Altronix Trove Mercury kits are pre-assembled and consist of Trove3M3 enclosure/backplane with factory installed Altronix power 
supply/charger(s) and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to sixteen (16) doors 
in a single enclosure.

Configuration Chart:

Altronix

Model Number

220VAC 50/60Hz Input Current (A)

Power Supply Board Input Fuse Rating

Power Supply Board Battery Fuse Rating

Nominal DC Output Voltage

Maximum 

Supply

Current for 

Main and Aux. 

Outputs on Power 

Supply board 

and ACM8(CB) 

Access Power 

Controller’s 

outputs

Fail-Safe/Fail-Secure or  Dry Form “C” Outputs

Current Per  ACM8(CB) Output 

(A)

ACM8(CB) Board  Input Fuse Rating

ACM8 Board Output Fuse Rating

ACM8CB Board Output PTC Rating

PD8UL Board Output Fuse Rating

PD8ULCB Board Output Fuse Rating

Power Supply 1 Power Supply 2

[DC]

[Aux]

[DC]

[Aux]

Output Range  (VDC)

Output Range  (VDC)

Output Range  (VDC)

Output Range  (VDC)

T3MK75F16V

4.8

6.3A/250V

5A/250V

15A/

32V

20.17-

26.4

20.28-

26.4

9.7-

13.2

10.03-

13.2

12VDC @ 9.3A
24VDC @ 9.2A

16

2.5

10A/

250V

2.5A/
250V

–

3.5A/
250V

–

T3MK75F16DV

4.8

6.3A/250V

5A/250V

15A/

32V

20.17-

26.4

20.28-

26.4

9.7-

13.2

10.03-

13.2

12VDC @ 9.3A
24VDC @ 9.2A

16

2.5

10A/

250V

–

2A

–

2.5A

T3MK77F16V

5.4

6.3A/
250V

15A/

32V

20.17-

26.4

20.28-

26.4

20.17-

26.4

20.28-

26.4

24VDC @ 9.2A

16

2.5

10A/

250V

2.5A/
250V

–

3.5A/
250V

–

T3MK77F16DV

5.4

6.3A/
250V

15A/

32V

20.17-

26.4

20.28-

26.4

20.17-

26.4

20.28-

26.4

24VDC @ 9.2A

16

2.5

10A/

250V

–

2A

–

2.5A

Hardware and Accessories:

•  Two (2) tamper switches (Altronix Model TS112 or equivalent).
•  Cam lock.
•  Battery leads.

Mechanical:

•  16 Gauge enclosure with ample knockouts for convenient access.
•   Enclosure Dimensions (H x W x D): 36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm).

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having 
jurisdiction. Product is intended for indoor use only. 
1.  Remove backplane from enclosure. Do not discard hardware.
2.  Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws 
 

in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.

Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install 

the three fasteners. Place the enclosure’s upper keyholes over the three upper screws. 

Install the three lower screws and make sure to tighten all screws.

3.  Mount included UL Listed tamper switches (Altronix Model TS112 or equivalent) in desired location, 
 

opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” 

from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input 

or the appropriate UL Listed reporting device. 

To activate alarm signal open the door of the enclosure.

4.  Mount Mercury boards to backplane, refer to pg. 3, 4.
5.  Refer to the eFlow Power Supply/Charger Installation Guide for eFlow104NBV, eFlow102NBV 
 

and corresponding Sub-Assembly Installation Guides for PD8UL(CB) and ACM8(CB) for 

further installation instructions.

6.  Position Mercury access controller module over corresponding spacers and depress onto 
 

snap on spacers (Fig. 2-3, pg. 3-4).

7.  Mount backplane to enclosure with hardware.

Fig. 1

Tamper Switch

(provided)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Enclosure