background image

IC NOTICE

This device complies with Industry Canada license-exempt 

RSS standard(s). Operation is subject to the following two 

conditions:
(1) This device may not cause interference, and

(2) This device must accept any interference, including 

interference that may cause undesired operation of the 

device.

Le présent appareil est conforme aux cnr d’Industrie 

Canada applicables aux appareils radio exempts de licence. 

L’exploitation est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et

(2) L’utilisateur de l’appareil doit accepter tout brouillage 

radioélectrique subi, même si le brouillage est susceptible 

d’en compromettre le fonctionnement.

TRADEMARKS

Alula, , and BAT-Connect are trademarks owned by 

Alula Holdings, LLC. Android is a trademark of Google LLC. 

Z-Wave is a registered trademark of Silicon Labs. Wi-Fi is a 

trademark of the Wi-Fi Alliance.

FCC WARNING

This equipment has been tested and found to comply with 

the limits for a Class B digital device, pursuant to part 15 

of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference 

by one or more of the following measures:
• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for 

help.
This device complies with Part 15 of the FCC rules. Operation is 

subject to the following two conditions:
(1) This device may not cause harmful interference.

(2) This device must accept any interference that may be received, 

including interference that may cause undesired operation.

Caution: any changes or modifications to this device not explicitly 

approved by manufacturer could void the user’s authority to 

operate this equipment.
The device has been evaluated to meet general RF exposure 

requirement. The device can be used in portable exposure 

condition without restriction.

Specifications

Physical Specifications

Wall Dimensions
Table Top Footprint
Weight
Pilot Hole for Screw into Wood
Pilot Hole for Wall Anchor
Mounting Fasteners

4.27in[10.84cm] x 7.42in[18.85cm] x 1.60[4.06cm] Deep
4.58in[11.64cm] x 7.42in[18.85cm] x 6.63[16.84cm] High
1.29lbs[585g]
Ø 1/8in [3mm]
Ø 3/16in [4.7mm]
#6 screws & 4 wall anchors (included)

Environmental Specifications

Operating Temperature
Maximum Humidity

32°F to 120°F (0°C to 49°C)
85% non-condensing relative humidity

Device Specifications

Battery Life
Power Transformer

Input
Output
Part Number

Terminal Block Wire Gauge
Wireless Range
Screen Resolution
Screen Size

4 hours

100-240vac 50/60hZ 0.5A
12VDC, 1A
RE012-6
16-24 AWG

~300 feet in open air
1024 x 600 pixels
7 inches diagonally

Accessories

Wi-Fi DeviceLink

RE926RX (only needed for )

Certifications

RE667-Pro

FCC, IC, RCM

Specifications subject to change without notice.

47-00018 • Rev B • 2022-04-01

Tech Support Line • (888) 88-ALULA • (888) 882-5852

alula.com

01

Summary of Contents for RE667-Pro













Reviews: