Installation Instructions
1170 N Red Gum St, Anaheim, CA 92806
© ALUZ All Rights Reserved. ALUZ reserves the right to make changes or withdraw specifi cations without prior notice.
info@aluz.lighting
aluz.lighting
866.ALUZ.LTG | 714.535.7900
A1 Series
|
Surface
ZIBI
Pivot RGBW
(A1-ZIBI-PVT-RGBW)
Page 1 of 11
Overview
4 / 29 / 2022 / Rev 2
READ ENTIRE GUIDE BEFORE STARTING INSTALLATION
Important Notice:
Verify correct luminaire was received with correct
color temperature, voltage, and wattage before cutting or installing.
ALUZ will not be responsible if incorrect luminaire is installed.
END VIEWS / DIMENSIONS
2.53”
2.62”
0° Tilt (Minimum)
3.53”
3.85”
90° Tilt (Maximum)
GENERAL FEATURES
Applications
Wall Washing Lighting
Lens
Tempered Clear Glass Lens
Optics &
Asymmetric
10° - 60° or Asymmetric Optics
Length
Built to Order (2’, 3’, or 4’ Increments)
Construction
Aluminum Extrusion
Weight
5.6 lbs (2’), 7.9 lbs (3’), 11.2 lbs (4’)
Mounting
Mounting Clips (Sold Separately)
Listing
Dry or Wet (IP65 or IP67) Location
UL1598, CSA C22.2#250.0
UL8750, CSA250
UL2108, CSA C22.2 #9
Driver
Integral
Temperature
Ratings
Operating / Startup: -20° to 48°C (-4° to 120°F)
Storage: -40° to 76°C (-40° to 170°F)
Installation Link
PRODUCT INFORMATION
• Lighting for wall washing, cove, edge, undercabinet, accent, displays
• Line Voltage (Integral Driver) or Low Voltage (Remote Driver)
• Color changing LEDs
• Available in 3 Watts up to 18 Watts Per Foot
• Product is shipped in 1’, 2’, 3’, and 4’ luminaires
• Available for outdoor rated installations
• Electric Hammer Drill
• 14.4 to 28 Volt Cordless Drill
• Phillips Bits
• Utility Knife
• Electrical Cord
• Marker
• Wire Stripper
• Long Nose Pliers
• Drill Bits - Concrete or Wood
• Electrical Three Ways
• Safety Glasses
• Measuring Tape
• Laser Line or Chalk Line
INSTALLATION TOOLS REQUIRED
ELECTRICAL REQUIREMENTS
• Line Voltage luminaires do not require a remote driver.
• Maximum load per line voltage fi xture is 320 watts per circuit.
ELECTRICAL
Dimming
DMX
Maximum Run
(Line Voltage
Integral Driver)
100’
(3W)
, 64’
(5W)
, 53’
(6W)
,
40’
(8W)
, 35’
(9W)
, 26’
(12W)
, 21’
(15W)
Luminaire Voltage
120V - 277V
(UNV)
Neutral (Blue)
Hot (Brown)
Ground (Green / Yellow)
Primary Voltage
120-277V AC
DMX
Signal
DMX+ (White)
DMX Shield (Sleeve)
DMX- (Blue)
DMX WIRING DIAGRAM (Dry or Wet Location)
DMX WIRING NOTES
• Default DMX address per RGBW luminaire.
DMX Address 001 = Red
DMX Address 002 = Green
DMX Address 003 = Blue
DMX Address 004 = White
• Consult third party DMX commissioner to modify at time of installation.
• Connection from DMX controller to luminaire must be made using a proper daisy
chain connection per DMX-512 / RDM standards.
• Do not make DMX wiring connections in parallel.
• When connecting DMX Shield to a DMX controller terminal, ensure that it is not
connected to or touching earth ground, chassis ground, and/or DC power (-) return.
