background image

 Always 

O

n UPS Systems

 

 

12.

 

Optional Extras 

12.1.

 

Procedure for (Optional) Extended Battery 
Cabinets 

 

Attention: 

Choose the correct battery pack voltage, according to the UPS rated 
capacity.  Do not connect too few or too many batteries, as this could 
cause electrical shock, damage or death.

 

 
 
 

Caution: 

It is important to follow the correct procedures for connecting the battery 
packs.  If the procedures are not followed properly, it will increase the 
chance of electrical shock, damage or death.  Follow the procedure to 
avoid any possible danger. 
 
 
 

Attention:

 

Ensure correct battery bank voltage and polarity before connecting. 
Ensure UPS is “OFF” and battery breaker(s) are “OFF” 
Do not connect the wires to the UPS first, electrical shock might occur. 
 
 
 

Caution: 

Observe the appropriate cable connections regulation (e.g. National 
Electrical Code – NEC in the USA) at all times.  Using cables of 
improper size may damage your equipment and cause fire hazards.  
Ground the UPS and the load equipment to a common point to prevent 
looping. 

 
 
 

1)

 

Battery Cabinet(s) should be installed as close as possible to the UPS system. 
(cable to be as short as possible) 

 
2)

 

The DC Voltage of the Battery Cabinet must be the same as the DC Voltage of 
the UPS system. Battery Bank Voltage is provided in Table 12.1.1. 

 

MODEL NO. 

BATTERY VOLTAGE 

700VA 24VDC 

1000VA  

36VDC 

1500VA 36VDC 
2000VA 72VDC 
3000VA  

72VDC 

 

Table 12.1.1

 UPS battery voltage configurations 

 

3)

 

Before connecting the Battery Cabinet to the UPS: 
i)

 

You Must Power down the UPS and remove input AC supply. 

ii)

 

If present: Battery Breaker MUST BE in the “Off” position on the UPS 
system and Battery Bank.  

M0309_N_Series_ABS_700-3kVA_User_Manual V2.8 2012-06-12 

25

 

Summary of Contents for GES-302N









































Reviews: