background image

Always “On” UPS Systems Inc. 

 

5

 

Version 1.4

 

5. AUDIBLE 

ALARM 

5.1. 

Back-Up (Slow Alarm) 

When in back-up mode, the LED flashes every 2 seconds and the UPS 
sounds an audible alarm.  The alarm stops when the UPS returns to line 
normal operation.  Press the “On/Off/Test/Silence” Button during back-up 
mode to silence the beeping. 
 

5.2. 

Low Battery (Rapid Alarm) 

In back-up mode, when the battery energy runs low, the UPS beeps 
rapidly, twice every second, until the UPS shuts down from battery 
exhaustion or returns to line normal operation. This alarm cannot be 
muted. 
 

5.3. 

Overload (Continuous Alarm) 

The UPS is overloaded when the connected load exceeds the maximum 
rated capacity of the UPS.  The UPS sounds a continuous alarm to warn of 
an overload condition.  Disconnect non-essential loads until the UPS stops 
the alarm, this will eliminate the overload. 
 

5.4. 

Replace Battery (Continuous Alarm) 

The UPS emits a continuous beep if the battery fails the self-test. See 
replace battery section for battery replacement or call your dealer for 
services. 
 

6. SOFTWARE 

OPTIONS 

6.1. UPSMON 

Software 

The UPSMON software uses the standard RS-232 interface to perform 
monitoring functions, and then provides an orderly shutdown of a 
computer in the event of power failure.  Moreover, UPSMON displays all 
the diagnostic symptoms through a graphical display, such as Voltage, 
Frequency, Battery Level, etc. 
 
The software is available for DOS, Windows 3.1x, Windows 95/98/00/XP 
& Windows NT V3.5 or later. 
 

6.2. Interface 

Kits 

A series of interface kits are available for various operating systems that 
provide UPS monitoring.  Each interface kit includes the special interface 
cable required to convert status signals from the UPS into signals that the 
individual operating system will recognize.  The interface cable at the UPS 
side must be connected to the REMOTE PORT, at the computer side it can 
be connected to either COM1 or COM2.  For other installation instructions 
and powerful features please refer to READ ME file included within the 
software. 

Caution: 

Use only factory supplied or authorized UPS monitoring kits!

 

Summary of Contents for Limousin II














Reviews: