background image

 

 

 

M1701_POS_Pro_Manual V1.0 2012-06-12 

1.

 

INTRODUCTION 

The P.O.S. Pro-Series is a Line Interactive UPS system that includes the newest and 
latest technology enhancements.  The Line Interactive technology with AVR function 
(on-line voltage boost-up & buck-down) allows for a wide input voltage range of 90 
to 150VAC.  The P.O.S. Pro-Series UPS is ideal protection for modern Point of Sale 
equipment.  After the UPS has been turned “On” it will protect the load from 
transients, spikes and other power aberrations.  In the event of a blackout (or severe 
brownout) the UPS will automatically switch to back-up mode and maintain power to 
the load until the battery reaches a low voltage state.  Also included with our UPS 
system is a cyclic self-testing function to verify both the operation of the UPS and the 
condition of the battery. 
 
The integrated DC power supply and multiple outlet configuration allows for 
complete versatility for today’s Point of Sale equipment.  The adapter cord included 
with every P.O.S. Pro is designed to plug directly into the printer and provide back-
up power in the event of utility loss. 
 

Interference to Radio/TV 

If this UPS causes interference to radio or television reception (this may be 
determined by turning the UPS off and on), try to correct the interference by one or 
more of the following measures: 
 
1.

 

Connect the equipment to an outlet on a different circuit from which the 
receiver is connected. 

2.

 

Increase the separation between the equipment and the receiver. 

3.

 

Re-orientate the receiving antenna. 

Summary of Contents for P.O.S. Pro 600VA
















Reviews: