background image

11

Dial Operation 

(some models only)

Dial option is available on some models only.

Oven Clearances

A—Allow at least 4" (10.2 cm) of clearance around top and sides of oven.

Proper air flow around oven cools electrical components. With restricted
air flow, oven may not operate properly and life of electrical parts is
reduced.

B—Allow at least 4" (10.2 cm) between air discharge on back of oven and

back wall.

No metal pans

DO NOT power spray

Heating

1.

Open oven door, place food in oven, and close oven door.

2.    Turn the power level knob to desired power level.

• Power level can be set at Low (17%), Defrost (33%), Medium (55%),

Med. High (77%), or High power (100%).

3.

Turn time entry knob clockwise until desired time displays.
• Cooking time can be set up to 10 minutes.
• If turning the timer knob for less than 2 minutes, turn it past 2 minutes

and then back to the desired time.

4.

Oven begins operation and time counts down.

5.

When cooking time elapsed, microwave energy stops and oven signal
sounds.

Interrupting Operation

Open oven door to interrupt operation or turn time entry knob counterclockwise
to “0”. To resume microwave oven operation, close oven door.
If time was changed to “0”, time will need to be reset.

Changing Time and Power/Canceling
Mistakes

Cooking time and power level can be changed at any time while the oven is
operating. Turn knob(s) to desired new setting. To set cooking time to zero,
turn time entry knob counterclockwise to “0”.

A

B

Summary of Contents for ALD10D













Reviews: