background image

Installation Instructions

APG 16 SEER “M” SERIES 2-4 Tons

Single Package Gas-Electric Heating & Cooling Units

ATTENTION INSTALLING PERSONNEL

Prior to  installation, thoroughly familiarize yourself with this 

Installation Manual. Observe all safety warnings. During in-

stallation or repair, caution is to be observed.
It is your responsibility to install the product safely and to 

educate the customer on its safe use.

  RECOGNIZE THIS SYMBOL

            AS A SAFETY PRECAUTION

Affix this manual and Users Information 

Manual adjacent to the unit.

19001 Kermier Rd., Waller, TX 77484

 

www.goodmanmfg.com • www.amana-hac.com

©

 2015-2019, 2021 Goodman Manufacturing Company, L.P.

 is a registered trademark of Maytag corporation or its related companies and is used under license. All rights reserved.

These installation instructions cover the 

outdoor 

installation 

of single package heating and cooling units. See the 

Specification Sheet applicable to your model for information 

regarding accessories.

NOTE:  

Please contact your distributor or our website for 

the applicable Specification Sheet referred to in this manual.

This Forced Air Central Unit Design complies with re-

quirements embodied in The American National Standard / 

National Standard of Canada shown below: 

ANSI Z21.47 / CSA-2.3 Gas-Fired Central Furnaces

“IMPORTANT - This product has been designed and manufactured to meet ENERGY STAR®

criteria for energy efficiency when matched with appropriate coil components. However, 

proper refrigerant charge and proper air flow are critical to achieve rated capacity and 

efficiency. Installation of this product should follow the manufacturer’s refrigerant charging

and air flow instructions. 

Failure to confirm proper charge and air flow may reduce energy 

efficiency and shorten equipment life.

IOA-3012F
05/2021

Only personnel that have been trained to install, adjust, 

service or repair(hereinafter, “service”) the equipment 

specified in this manual should service the equipment. The 

manufacturer will not be responsible for any injury or 

property damage arising from improper service or service 

procedures. If you service this unit, you assume responsi-

bility for any injury or property damage which may re-

sult. In addition, in jurisdictions that require one or more 

licenses to service the equipment specified in this manual, 

only licensed personnel should service the equipment.  

Improper installation, adjustment, servicing or repair of 

the equipment specified in this manual, or attempting to 

install, adjust, service or repair the equipment specified in 

this manual without proper training may result in product 

damage, property damage, personal injury or death.

WARNING

Summary of Contents for APG 16 M Series

































Reviews: