INSTALLATION
NOTE: Due to the many different materials used to build walls, it is highly recommended
that you consult your local builder before you install this appliance on a wall.
Important note: The optional surround is fixed with 2 screws
unscrewing 2 screws and pulling off. It is recommended that two people remove the
surround.
Preparation
1. Select a location that is not prone to moisture and is located at least 0.91m or 3 feet away
from combustible materials such as curtains, drapes, furniture, bedding, paper, etc.
2. Mark the desired location on the floor and store the app
free place.
3. Prepare a wall with a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and
Prior to installing, test the appliance to make sure the appliance is fully operational by
plugging the power supply cord into a 120 Volt grounded outlet.
The rough wall opening size of the fireplace:
W(“)
BI-40-DEEP-XT
40
BI-50-DEEP-XT
50
BI-60-DEEP-XT
60
BI-72-DEEP-XT
73 1/2
BI-88-DEEP-XT
89 1/2
13
NOTE: Due to the many different materials used to build walls, it is highly recommended
builder before you install this appliance on a wall.
Important note: The optional surround is fixed with 2 screws and can be removed by
unscrewing 2 screws and pulling off. It is recommended that two people remove the
Select a location that is not prone to moisture and is located at least 0.91m or 3 feet away
from combustible materials such as curtains, drapes, furniture, bedding, paper, etc.
Mark the desired location on the floor and store the appliance in a safe, dry and dust
Prepare a wall with a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and other applicable regulations.
Prior to installing, test the appliance to make sure the appliance is fully operational by
plugging the power supply cord into a 120 Volt grounded outlet.
The rough wall opening size of the fireplace:
D(“)
H(“)
12 1/2
30
12 1/2
30
12 1/2
30
12 1/2
30
12 1/2
30
NOTE: Due to the many different materials used to build walls, it is highly recommended
builder before you install this appliance on a wall.
and can be removed by
unscrewing 2 screws and pulling off. It is recommended that two people remove the
Select a location that is not prone to moisture and is located at least 0.91m or 3 feet away
from combustible materials such as curtains, drapes, furniture, bedding, paper, etc.
liance in a safe, dry and dust
Prepare a wall with a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
other applicable regulations.
Prior to installing, test the appliance to make sure the appliance is fully operational by
W(“)
D(“)
H(“)
BI-40-DEEP-XT
(DE-T190040-01)
40
12 1/2
30
BI-50-DEEP-XT
(DE-T190050-01)
50
12 1/2
30
BI-60-DEEP-XT
(DE-T190060-01)
60
12 1/2
30
BI-72-DEEP-XT
(DE-T190072-01)
73 1/2
12 1/2
30
BI-88-DEEP-XT
(DE-T190088-01)
89 1/2
12 1/2
30
The models are designed to be built
stone, tile, etc) to be built right down to the glass edge. However, that application is not
always desirable or available so the surround could be used as an alternate finish option.
models are designed to be built-in. These units allow for the finishing material (drywall,
stone, tile, etc) to be built right down to the glass edge. However, that application is not
ays desirable or available so the surround could be used as an alternate finish option.
in. These units allow for the finishing material (drywall,
stone, tile, etc) to be built right down to the glass edge. However, that application is not
ays desirable or available so the surround could be used as an alternate finish option.
