background image

 

Characteristics

 

      Basic characteristics 

Module  

Name  

AGT 200 

Technology  

GSM ,GPRS, GNSS, BLUETOOTH 

 

GNSS  

GNSS  

GPS, GLONASS, GALILEO, BEIDOU, QZSS,

 

DGPS 

Receiver  

Tracking: 33/99 acquisition channels 

Tracking sensitivity  

-165 dBM  

Accuracy  

< 3 m  

Hot start  

< 1 s  

Warm start  

< 25 s  

Cold start  

< 35 s  

 

Cellular  

Technology 

GSM/GPRS 

2G bands  

Quad-band 850/900/1800/1900 MHz 

GPRS 

GPRS Mobile Station Class B 

Data transfer  
 

GPRS Multi-Slot Class 12 (up to 240 kbps) 

Data support 

SMS (text/data) 

 

Power  

Input voltage range  

10-30 V DC with overvoltage protection  

Back-up battery  

550 mAh 8,4V Ni-MH battery 

2 W max.

 

Current consumption  

at 12 V 

GPRS: average 69 mA  
Nominal: average 39 mA 
GNSS sleep: average 24 mA 
Deep Sleep: average 7.5 mA 
Online Deep Sleep: average 2.4 mA 

2 W max.

 

Current consumption  

at 24 V 

GPRS: average 35 mA 
Nominal: average 20 mA 
GNSS sleep: average 12,5 mA 
Deep Sleep: average 3,8 mA 
Online Deep Sleep: average 1.3 mA 

Interface  

Digital Inputs  

Digital Outputs 

4  

Analog Inputs 

1-Wire temperature sensors 

1-Wire iButton 

1  

RS232 

RS485 

1  

CAN J1939 

J1708 

K-Line 

LVCAN/ALLCAN 

GNSS antenna 

External High Gain 

GSM antenna 

External High Gain 

USB 

2.0 Mini-USB 

LED indication 

2 status LED lights 

SIM 

2x SIM Card (Dual-SIM) 

Summary of Contents for AGT200












Reviews: