background image

 

Battery discharge temperature  

-20 °C to +60 °C  

Battery storage temperature  

-20 °C to +45 °C for 1 month  
-20 °C to +35 °C for 6 months 

Features  

Sensors  

Accelerometer  

Scenarios  

Green Driving, Over Speeding detection, Jamming 
detection, GNSS Fuel Counter, Excessive Idling detection, 
Unplug detection, Towing detection, Crash detection, Auto 
Geofence, Manual Geofence, Trip  

Sleep modes  

GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep 
Sleep  

Configuration and firmware update  

FOTA Web, FOTA, Amber Configurator (USB, Bluetooth), 
FMBT mobile application (Configuration)  

SMS  

Configuration, Events,Debug  

GPRS commands  

Configuration,Debug  

Time Synchronization  

GPS, NITZ, NTP  

Fuel monitoring 

OBDII 

Ignition detection  

Accelerometer, External Power Voltage, Engine  

 

 

 

  Safety information  

 

         

This message contains information on how to operate AIT 210 safely. By following these  

 

 

requirements and recommendations, you will avoid dangerous situations. You must read  

 

 

these instructions carefully and follow them strictly before operating the device!  

 

•  The device uses SELV limited power source. The nominal voltage is +12 V DC. The  

 

 

allowed voltage range is +12...+30 V DC.  

•  To avoid mechanical damage, it is advised to transport the device in an impact-proof  

 

 

package. Before usage, the device should be placed so that its LED indicators are  

 

 

visible. They show the status of device operation.  

•  Before unmounting the device from vehicle, ignition MUST be OFF. 

 

 

Do not disassemble the device. If the device is damaged, the power supply cables 
are  not  isolated  or the  isolation  is  damaged,  DO  NOT touch the  device  before 
unplugging the power supply.  
 

 

 

All wireless data transferring devices produce interference that may affect other 
devices which are placed nearby.  
 

 

Please consult representatives of your vehicle model regarding OBDII location on 
your vehicle. In case you are not sure about proper connection, please consult 
qualified personnel. 

 

 

 

 

The programming must be performed using a PC with autonomic power supply.  
 

 

 

Installation and/or handling during a lightning storm is prohibited.  
 

 

 

The device is susceptible to water and humidity.  
 

Summary of Contents for Amber Insight T251









Reviews: