background image

 

Version 1.1  

 

©Copyright 2015, Ambient LLC. All Rights Reserved. 

 

 

 

Page 2 

 

1

 

Introduction 

Thank you for your purchase of the Ambient Weather WS-16 Wireless 8-Channel Thermometer with 
Daily Min/Max Display. The following user guide provides step by step instructions for installation, 
operation  and  troubleshooting.  To  download  the  latest  manual  and  additional  troubleshooting  tips, 
please visit the FAQ website: 

 

http://ambientweather.wikispaces.com/ws16 

 

The WS-16 supports any combination of the following sensors and receivers (additional sensors and 
receivers are sold separately): 
 

Item Number 

Image 

Description 

F007T 

 

8-channel sensor measures temperature. Applications 
include indoor and outdoor air temperature 
measurement. 

F007TP 

 

8-channel sensor measures probe temperature. 
Applications include refrigerators and freezers (where 
the probe is placed inside the appliance(s) and the 
display is outside), water temperature, soil temperature 
and ground temperature. 

F007PF 

 

8-channel pool float thermometer. Applications include 
pools, spas, and lakes. 

WS-14-C 

 

Add as many display consoles as you like to your 
existing system. For example, you can have one remote 
sensor display temperature and place a display console 
in every room. 

 

 

Summary of Contents for WS-16















Reviews: