American Aldes 1500 SFDE Operation And Installation Manual Download

Page: 5 / 16

Function & Controls

Model(s) HRV 1500 SFD / SFDE

Basic Functions

Speed control is obtained by powering 24V to one of the
designated speed taps.

Example:

A jumper between the R terminal and the G terminal will
result in low speed operation.

Setup

Select appropriate operational speed by installing the
jumper wire between one of the designated speed taps. (A
jumper wire is factory installed in the low speed position.)

Note:

It is recommended to use the optional speed control Part
# 28-895 in order to obtain full fan speed control.

Optional Speed Control
Part #28 885

Micro Processor Board

Optional Remote
Dehumidistat
Part #28-882

Boosts unit to
high speed when
humidity is higher
than setpoint

Optional DVC
Control
Part #28-883
Same as above
with On/OFF
switch and high
speed boost
switch

Optional DET
Timer
Part #28-879

Boosts to high
speed for 20, 40,
60 minutes

Summary of Contents for 1500 SFDE

















Search results

Summary of Contents for 1500 SFDE

Reviews:

Related manuals for 1500 SFDE

Brands by name

Popular brands

American Aldes 1500 SFDE, Operation And Installation Manual

Search results

Summary of Contents for 1500 SFDE

Reviews:

Related manuals for 1500 SFDE

Brands by name

Popular brands