background image

When you have finished using the CD player, before switching off the power be sure that the disc holder has
been closed with the OPEN/CLOSE button (Figure 15).

CAUTION: Do not forcibly close the disc holder when the power is off.

Do not switch off the power when

the disc holder is open.

Switch off the power after the disc holder has 

been closed with the OPEN/CLOSE button.

1. Precautions on handling compact discs

Do not allow fingerprints, oil or dust to get 
on the surface of the disc.  If the disc is 
dirty, wipe it off with a soft dry cloth.

Do not use benzene, thinner, water, record 
spray, electrostatic-proof chemicals, or 
silicone-treated cloths to clean discs.

• 

Always handle discs carefully to prevent 
damaging the surface; in particular when 
removing a disc from its case or returning it.

Do not bend the disc.

Do not apply heat.

Do not enlarge the hole in the center of the 
disc.

• 

Do not write on the label (printed side) with 
a hard-tipped implement such as a pencil 
or ball point pen.

Condensation will form if a disc is brought 
into a warm area from a colder one, such as
outdoors  in winter.  Do not attempt to dry`
the disc with a hair dryer, etc. 

2. Precaution on storage 

After playing a disc, always unload it from 
player. 

• 

Always store the compact disc in the jewel 
case, protecting from dirt or  damage. 

Do not place discs in the following areas: 

a)  Areas exposed to direct sunlight for a 

considerable time. 

b)  Areas subject to accumulation of dust or 

high humidity. 

c)  Areas affected by heat from indoor heaters, 

etc.

BEFORE SWITCHING OFF THE POWER

COMPACT DISCS

Fig. 15

American DJ

®

AUDIO • DCD-PRO200™ INSTRUCTIONS MANUAL • PAGE 13

BASIC OPERATION (CONT.)

13. Loop Play

Press the LOOP button to set the loop start point A, the LOOP indicator will flash on the LCD.

Press the LOOP button again to set the loop end point B. After the B point is set the playback will
enter the loop play from A to B repeatedly.

Press the LOOP button again, the loop play function is canceled, the LOOP indicator goes out.

Summary of Contents for PROformer DCD-PR200 MK2














Reviews: