background image

  WiFLY Bar QA5                                   Safety Precautions

ADJ Products, LLC  -  www.adj.com  - WiFLY Bar QA5 User Manual Page 4

ADJ Products, LLC  -  www.adj.com  - WiFLY Bar QA5 User Manual Page 3

•  Rechargeable Lithium Battery

•  Mulit-Colors

•   Five Operating Modes

•  Electronic Dimming 0-100%

•   Built in Microphone

•   DMX-512 protocol

•  3-Pin DMX Connection

•   6 DMX Channel Modes: 4 Channel Mode, 6 Channel Mode, 7    

  Channel Mode, 8 Channel Mode, 9 Channel Mode, & 22 Channel  

   Mode

•  Built-In ADJ’s WiFly TransCeiver Wireless DMX

•  ADJ RFC compatiable (Not Included)

•  Power Cord Daisy Chain (See page 14)

•   To reduce the risk of electrical shock or fire, do not expose this unit  

   rain or moisture

•   Do not spill water or other liquids into or on to your unit.

•   Do not attempt to operate this unit if the power cord has been   

   frayed or broken. Do not attempt to remove or break off the ground 

   prong from the electrical cord. This prong is used to reduce the risk  

   of electrical shock and fire in case of an internal short.

•   Disconnect from main power before making any type of connection.

•   Do not remove the cover under any conditions. There are no user  

   serviceable parts inside.

•   Never operate this unit when it’s cover is removed.

•   Never plug this unit in to a dimmer pack

•   Always be sure to mount this unit in an area that will allow proper  

   ventilation. Allow about 6” (15cm) between this device and a wall.

•   Do not attempt to operate this unit, if it becomes damaged.

•   This unit is intended for indoor use only, use of this product out`  

   doors voids all warranties.

•   During long periods of non-use, disconnect the unit’s main power.

•   Always mount this unit in safe and stable matter.

•   Power-supply cords should be routed so that they are not likely to  

   be walked on or pinched by items placed upon or against them,  

   paying particular attention to the point they exit from the unit. 

• Cleaning -The fixture should be cleaned only as recommended by  

  t he manufacturer. See page 30 for cleaning details.

•   Heat -The appliance should be situated away from heat sources  

   such as radiators, heat registers, stoves, or other appliances (inclu-

   d ing amplifiers) that produce heat.

•   The fixture should  be serviced by qualified service personnel when:

    A. The power-supply cord or the plug has been damaged.

    B. Objects have fallen, or liquid has been spilled into the appliance.

    C. The appliance has been exposed to rain or water.

    D. The appliance does not appear to operate normally or exhibits a  

         marked change in performance.

  WiFLY Bar QA5    

                   Warranty Registration

  WiFLY Bar QA5                                                     Features

The WiFLY Bar QA5 carries a 3 year limited warranty. Please fill out 

the enclosed warranty card to validate your purchase. All returned 

service items whether under warranty or not, must be freight pre-paid 

and accompany a return authorization (R.A.) number. The R.A. number 

must be clearly written on the outside of the return package. A brief 

description of the problem as well as the R.A. number must also be 

written down on a piece of paper included in the shipping carton. If 

the unit is under warranty, you must provide a copy of your proof of 

purchase invoice. You may obtain a R.A. number by contacting our 

customer support team on our customer support number. All pack-

ages returned to the service department not displaying a R.A. number 

on the outside of the package will be returned to the shipper.

The unit should be mounted using a mounting clamp (not provided), 

affixing it to the mounting bracket that is provided with the unit. 

Always ensure that the unit is firmly fixed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you 

are attaching the unit is secure and is able to support a weight of 10 

times the unit’s weight. Also, always use a safety cable that can hold 

12 times the weight of the unit when installing the fixture.

The equipment must be installed by a professional, and it must be 

installed in a place where it is out of the reach of people’s grasp.

  WiFLY Bar QA5                                                 Installation

Summary of Contents for WIFLY BAR QA5

















Reviews: