American Dryer Corp. ML-130 III Installation Manual Download | Manualshive

Page: 5 / 28

background image

113335 - 12

www.amdry.com

5

Articles left in the dryer after the drying and
cooling cycles have been completed can create a
fire hazard.

▲

WARNING

!

Do not operate steam dryers with more than 125 psi (8.61
bar) steam pressure. Excessive steam pressure can damage
steam coil and/or harm personnel.

Replace leaking flexible hoses or other steam fixtures
immediately. Do not operate the dryer with leaking flexible
hoses. Personal injury may result.

Read and follow all caution and direction labels attached to
the dryer.

For safety, proper operation, and optimum performance, the
dryer must not be operated with a load less than sixty-six
percent (66%), 80 lb (36.3 kg) of its rated capacity.

You must disconnect and lockout the electric
supply and the gas supply or the steam supply
before any covers or guards are removed from the
machine to allow access for cleaning, adjusting,
installation, or testing of any equipment per OSHA
standards.

▲

WARNING

!

IMPORTANT: Dryer must be installed in a location/
environment, which the ambient temperature remains
between 40° F (4.44° C) and 130° F (54.44° C).

Notes ______________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

Notes ______________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

«
...
3
4
5
6
7
...
»

Summary of Contents for ML-130 III





























Reviews:

No comments

Related manuals for ML-130 III

Airbrush Duo 76650-UK

Brand: T3 Pages: 17

Brand: PALSON Pages: 52

AirCook Q70 XXL

Brand: Tesla Pages: 46

Brand: T-Fal Pages: 34

Easy Pro Series

Brand: TEFAL Pages: 18

Brand: Kalorik Pages: 24

Brand: Smeg Pages: 32

Brand: IRT Hyperion Pages: 28

Brand: Maestro Pages: 48

Brand: Adler Europe Pages: 64

Brand: Adler Europe Pages: 64

Brand: Adler Europe Pages: 68

Brand: IPSO Pages: 43

AWD 1200 Instructions for and use

Brand: Ariston Pages: 16

Brand: Zanussi Pages: 12

Brand: Zanussi Pages: 12

Brand: Zanussi Pages: 13

Brand: Zanussi Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands