background image

2

SRS-40 Owner’s Manual

Safety Decals (From Kit PN 22418)

WARNING

DANGER

WARNING

WARNING

WARNING

WARNING

WARNING

Hot parts can

cause severe

burns.

Do not touch any

internal surfaces

during or shortly

after operation.

All hoses should be

connected in full

compliance with

federal state and

local codes and

regulations.

Safety devices should

be tested in 

accordance with

manufacturer’s

recommendations.

Do not remove caps,

plugs, or other

components while

the compressor

is running or has 

pressure in the tank.

Disconnect power and 

relieve all pressure

prior to maintenance.

Do not use air from

this compressor for

breathing or for the

processing of  

consumables except

in full compliance with

federal, state, and

local codes and

regulations.

Read the operation 

manual prior to use of 

this unit.

Failure to adhere to

instructions can result

in personal injury.  

Replacement manuals

can be purchased

from:

American Eagle

190 State Street

Garner, Iowa 50438

Rotating parts can 

cause serious injury.

Keep body parts clear

while unit is in

operation.

Never operate this unit

without cover 

completely attached.

High pressure

hydraulic system.

Do not attempt to search

for leaks with hand or 

other part of the body.

Doing this can cause 

subcutaneous injection 

or amputation.

Paper should be

used to check for

hydraulic leaks.

Summary of Contents for SRS-40





































Reviews: