Plus and Minus button function switch
Short press the target key to switch between speed and slope adjustment functions. Short press
the target key and when the main window displays the incline figure, press plus or minus key to
adjust the slope. Short press the target key and when the main window displays the speed, press
plus or minus key to adjust the speed.
16
Product Maintenance
Common Failures and Troubleshooting 15
Safety lock function
In any state, pull off the security lock, the window displays "E07", and the buzzer rings “BI-BI-BI”
three times. If the motor is running, it’ll reach an emergency stop. When the safety lock is off, it
cannot be started or operated.
8. Common Failures and Troubleshooting
Please call our dealer or our after-sales service team if you have any other questions.
Questions Possible Causes
Maintenance Methods
Treadmill
does not work.
The running
belt doesn't
run smoothly.
Running belt
slipped.
Not connected.
Power is not turned on.
Safety lock dropped.
Circuit signal system broken.
Fuse blew out.
Insufficient lubrication.
Belt is too tight.
Running belt too loose.
Running belt too tight.
Insert plug into socket.
Put the power switch in position "ON".
Put the safety lock in the correct position.
Check the controller input terminal and signal circuit.
Replace the fuse.
Add silicone oil lubricant.
Adjust belt tightness.
Adjust running belt tightness.
Adjust running belt tightness.
Error messages on electronic meter and elimination methods.
Questions Possible Causes
Maintenance Methods
E01
E02
E03
E04
E05
E06
E07
Abnormal display
Poor connection.
The motor wire is loose or
falling off, or the carbon brush is
worn out.
Not detecting signal.
Controller or motor not working.
Overload protect activated.
System self-check failed.
Safety lock dropped.
External disturbance.
The signal line is not plugged it. Plug it in again.
Check whether the motor cable is loose or falling off. If it
does not fall off, check whether the carbon brush of the
motor is worn out. If it is worn out, replace the motor. If it is
not worn out, the electric controller is damaged. Replace
the electric controller.
Sensing wire is not plugged in properly. Plug it in again correctly.
Probeable overload. Replace controller or motor.
Overload. Replace controller.
System failure. Replace controller.
Put the safety lock in the correct position.
Turn off power switch,turn on it after one minute.
9. Product Maintenance
1. Lubrication
When the running belt is used for a period of time, it must be Iubricated with special methy silicone oil.
Advice:
1 hour or less per week lubricate once every 6 months
Less than 3 hours per week lubricate once every 3 months
3-6 hours per week lubricate once every 2 months
More than 6 hours per week lubricate once a month
Do not lubricate too much. It is not the more lubricants, the better.
Remember: Proper lubrication is an important factor in improving the life of the treadmill.
2. The method to check if you need to add lubricant.
Grab the running belt and touch the middle of the running belt back
with your hands as much as possible.You don’t need to add lubricant if you have silicone on your
hand (a little damp). You have to add lubricant if the pad is dry and there is no silicone on your hand.
The step of lubricating on the running plate (as shown in
the right picture).
Stop running and fold the machine.
Lift the running belt of the underside of the main body,
and put the oil pot as far as possible into the middle of
the running belt. And spray methyl silicone oil inside
the running belt and all the contacting area.
You can keep the treadmill running in speed of 1km/h to
evenly lubricate then step on the running belt from left
to right. After a few minutes, the methyl silicone oil can
be completely absorbed by the running belt.
