background image

 

 

 

19148 Winch Installation Guide Rev A 

Page 1 of 10 

18931-R 2500 Lb. Winch with Nylon Rope  

19148

 – Winch Installation Guide 

SPECIAL REQUIREMENTS:  Used on both Standard Cab & Crew Cab  

 

TOOLS REQUIRED 

 

ESTIMATED INSTALL 
TIME 

RECOMMENDED SKILL 
LEVEL 

Philips Screw Driver 

General Purpose Pliers 

2 Hours 

Intermediate 

½” Socket & Ratchet 

Wire Cutters 

 

 

½” Wrench 

9/16” Wrench 

 

 

4 mm Allen Wrench 

9/16” Socket & Ratchet 

 

 

7/16” Wrench 

7/16” Socket & Ratchet 

 

 

3/8” Socket & Ratchet 

 

 

 

 

Before you begin, check the contents of the kit against the parts list below.  Immediately contact American Landmaster with any questions or 

discrepancies.  American Landmaster cannot assume responsibility for any damage or injury resulting from incorrect installation of parts.  American 

Landmaster suggests that accessory kits be installed by an authorized American Landmaster dealer or service center. 

 

                                                       !!  WARNING  !!   

 

 

 

 

                      

Serious Injury or death could occur! 

• Use proper personal protective equipment during installation of this kit.  Use safety glasses. 

 

 

 

(1)

 

 Winch with Nylon Rope     (1)     Winch Harness   

      (1)    Contactor with cables       (1)   Winch Bumper Bracket & Bolts 

(1)

 

 Winch Switch     

(2)     Winch Mounting bolts   (12)   Tie Wraps       

             (3)   Christmas Tree Tie Wraps 

(1)

 

Remote Winch Connector Cap          (4)    Remote Connector Mounting Screws #6            (4)   Remote Connector Lock Nuts #6 

(1)

 

Remote Winch Switch 

(4)   1.5” by ¼” Contactor Mounting Bolts 

                             (4)   1/4” Contactor Lock Nuts 

 

 

Fig 1 – Kit contents – 2500 Pound Winch 

PARTS LIST FOR AMERICAN LANDMASTER ACCESSORY KIT 

Summary of Contents for 18931-R











Reviews: