American Landmaster 18931-R Installation Instructions Manual Download

Page: 8 / 10

19148 Winch Installation Guide Rev A

Page 8 of 10

Figure 12: Winch Connector on Instrument Panel Harness

Connect the four pin connector of the winch harness to the open connector on the instrument panel harness.

Remove the rubber plug from the right most hole on the instrument panel.

Figure 13: Remote Winch Plug

Figure 14: Remote Winch Switch Connector Orientation

Place the gray three pin connector through this hole with the connector oriented as shown in the picture.

Use the four #6 screws and nuts to attach this connector to the instrument panel face.

Use a Philips screwdriver to start threading the screws into the connector. This will hold the connector in place on the
dash panel. Push the connector toward the dash panel from behind with one hand during this step.

10.

Start the nuts on the back side to fully secure the connector.

11.

Use a Philips screw driver on the front and a pliers on the back to complete the fastening of the connector.

12.

Install the gray cap with a quarter turn when you are not using the remote winch switch.

Winch Connector

Remove

Receptacle with No Notch on Top

Notch

Remove

Notch

Remove

Summary of Contents for 18931-R











Search results

Summary of Contents for 18931-R

Reviews:

Related manuals for 18931-R

Brands by name

Popular brands

American Landmaster 18931-R, Installation Instructions Manual

Search results

Summary of Contents for 18931-R

Reviews:

Related manuals for 18931-R

Brands by name

Popular brands