American Standard Paradigm Selectronic 7025.1 Series Installation Instructions Manual Download

Page: 1 / 9

M965985 (11/18)

Installation Instr

uctions

Certified to comply with ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at:

www.americanstandard-us.com

or e-mail us at:

CRTTEAM@lixilamericas.com

For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

Paradigm

™

Selectronic

Integrated

Faucet with Optional Above-Deck Mixing

& SmarTherm

MODEL NUMBERS

7025.1xx 702B.1xx
7025.2xx 702B.2xx
7025.3xx 702B.3xx

CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.

Product No’.s & Options

Specifications

Faucet Installation

Electrical Installation

4-5

FAQ’s / Troubleshooting

Parts

Start-up / Maintenance

6-8

Summary of Contents for Paradigm Selectronic 7025.1 Series










Search results

Summary of Contents for Paradigm Selectronic 7025.1 Series

Reviews:

Related manuals for Paradigm Selectronic 7025.1 Series

Brands by name

Popular brands

American Standard Paradigm Selectronic 7025.1 Series, Installation Instructions Manual

Search results

Summary of Contents for Paradigm Selectronic 7025.1 Series

Reviews:

Related manuals for Paradigm Selectronic 7025.1 Series

Brands by name

Popular brands