02
1.
Prior to Installation:
• Remove protective plastic and packaging and carefully inspect for any
damage.
• Check tub for correct model name, size, color and trim finish.
• The tub MUST be tested while pump, electrical systems, and piping
(plumbing) are accessible.
• If there are any issues, do not install and report the issues immediately
to our factory or the authorized dealer.
2.
WARNING:
To avoid injury, exercise caution when entering or exiting the
bathtub.
3.
DANGER/WARNING:
To reduce the risk of injury, do not permit children or
persons with a disability to use this unit unless they are closely supervised
at all times. Risk of accidental injury or drowning. Children should not use
hydromassage bathtub without adult supervision.
4.
WARNING:
Risk of accidental injury or drowning; Do not use hydromassage
bathtub unless all suction guards are installed to prevent body and hair
entrapment.
5. This product is for indoor use only. Use the bathtub only for its intended
purpose as described in this manual and do not use attachments or accessories
which are not recommended by manufacturer.
6. Never drop or insert any objects into any openings.
7. Persons with long hair should wear a bathing cap when using the bathtub.
8.
WARNING:
Risk of accidental injury or drowning; do not use drugs or alcohol
before or during the use of a bathtub or hydromassage bathtub equipped
with heater to avoid unconsciousness or possible drowning.
9.
WARNING:
Risk of Fetal Injury; pregnant or possibly pregnant women should
consult a physician before using a hydromassage bathtub equipped with
heater.
10. The bathtub must be connected to an electrical supply circuit that is
protected by a ground fault circuit interrupter (GFCI) which is provided
by the installer. The GFCI should be tested periodically to ensure that it is
working properly.
11. Keep all appliances, such as radios and hair dryers, a safe distance from the
bathtub.
12. For permanently connected units, green colored terminal (or a wire connector
marked “G”, “GR”, “Ground”, or “Grounding”) is provided within the terminal
compartment. To reduce the risk of electrical shock, connect this terminal or
connector to the grounding terminal of your electrical service or supply panel
with a conductor equivalent in size to the circuit conductors supplying this
equipment.
13. Install in accordance with manufacturer’s installation instructions. Failure
to comply with all instructions, requirements and warnings contained in this
manual creates a serious hazard to the bathtub user and may result in serious
personal injury.
Warning:
The causes, symptoms, and effects of hyperthermia may be described
as follows: Hyperthermia occurs when the internal temperature of the body
reaches a level several degrees above the normal body temperature of 98.6. The
symptoms of hyperthermia include an increase in the internal temperature of the
body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia
include (1) failure to perceive heat, (2) failure to recognize the need to exit
the spa or hot tub, (3) unawareness of impending hazard, (4) fetal damage
to pregnant women, (5) physical inability to exit the spa or hot tub, and (6)
unconsciousness resulting in the danger of drowning.
Warning:
The use of alcohol, drugs, or medication can greatly increase the risk
of fatal hyperthermia.
SAVE THESE INSTRUCTIONS
Americh baths are assembled complete and ready for installation.
Immediately upon receiving the bath and removal of packing, INSPECT
the unit for freight damage. Any claims for damage, whether apparent
or hidden, must be made to freight carrier immediately, in order for them
to assume all associated costs. Should inspection reveal any defect in the
finish, DO NOT INSTALL THE BATH. Damage or defect to the finish claimed
after the bath is installed is excluded from the warranty. The warranty DOES
NOT cover labor or materials to remove or re-install the bath.
PRIOR TO INSTALLATION
Check to ensure that:
1. The installation will conform with all applicable Federal, State and Local
Building Codes & Regulations;
2. The unit is the correct model and color;
3. There has been no shipping damage;
4. The “notice” or “warning” tags on the bathtub have been read and thoroughly
understood;
5. The interior of the tub will be protected during installation;
6. Make sure sub floor is level.
DURING INSTALLATION
Check to ensure that:
1. Bathtub is not hanging from the rim. Bath must be supported from the floor
(See Figure 1, Page 4.)
2. An access panel with minimum dimensions of 16” height by 20” width is
required. See specification sheet for proper access panel location.
3. All Bathtubs with seats must have additional support for each seat.
4. All building materials and wiring should be routed away from the pump body
or other heat producing components of the unit.
ELECTRICAL REQUIREMENTS
Manufacturer recommends a dedicated 20 amp circuit breaker for each power
cord supplied on your whirlpool bathtub.
WARNING
- When using electrical
products, basic precautions should always be followed, including the following:
1.
DANGER: Risk of electric shock.
Connect only to a supply circuit protected
by a Class A ground-fault circuit-interrupter (GFCI). Test on a routine basis.
2. Grounding is required. The unit should be installed by a qualified service
representative and grounded.
3. (For built-in and custom units) install to permit access for servicing.
4. Supply 110 Volt electrical outlet. This circuit must be protected by a ground
fault circuit interrupter (GFCI.)
5. Plug supply cord(s) into electrical outlet.
6. To test the GFCI, do the following:
a. Push the test button;
b. Check to see that power has been interrupted;
c. Push the reset button;
d. Check to see that power has been restored.
If the GFCI does not operate properly during the test, there is a ground current
flowing indicating the risk of electric shock. Do not use this unit. Disconnect the
unit and have the problem corrected by a qualified service representative before
using.
Refer to Operating Instructions for system operations and wiring diagrams.
Warning:
Whirlpool bathtubs utilize acrylic and fiberglass materials (which are inherently slippery surfaces), electricity, water, air pressure and suction. The
following basic safety precautions should always be followed when using your bathtub.
CAREFULLY
READ AND FOLLOW ALL INSTRUCTIONS
before attempting to operate your whirlpool or Airbath® Bathtub.
IMPORTANT SAFETY INSTRUCTIONS
:
pertaining to a risk of fire, electric shock, or injury to persons
