ReFlex Power™ Controller
ReFlex Power™
3-10
M380056-01 Rev L
3.4
INSTALLATION
This section provides instructions for inspection, installation and initial
performance check.
3.4.1
I
NTRODUCTION
The ReFlex Power™ Controller module has been fully tested prior to shipment;
and the module is ready for immediate use upon receipt. However, when first
unpacked, the module should be inspected to ensure that no shipping damage
has occurred.
3.4.2
I
NITIAL
I
NSPECTION
Perform a visual inspection of the shipping container prior to accepting the
package from the carrier. If damage to the shipping container is evident, a
description of that damage should be noted on the carrier's receipt and signed by
the carrier's driver.
Verify that the proper module and associated accessories have been received,
per the Bill of Materials. Perform a visual inspection of the module after it is
removed from the shipping container. Check for shipping damage such as dents,
scratches, or distortion of the enclosure.
If external damage is evident, there may be internal damage as well. Immediately
contact the carrier and file a claim for concealed damage. In addition, the
shipping container and filler material should be saved for inspection. Forward a
report of the damage to the Customer Care Department where an associate will
provide instructions for repair or replacement of the unit.
3.4.3
L
OCATION
C
ONSIDERATIONS
The RFPC module is designed for use within the ReFlex Power™ Mainframe and
can be inserted within any slot of the Mainframe. Since the module is fan–cooled,
it requires adequate clearance at the air intake of the front panels so that airflow
is not impeded.
A
IRFLOW
R
EQUIREMENTS
Provide adequate clearance for adequate air intake through the front
panels and exhaust through the rear.
Ensure that the ambient air temperature at the front panel air intake does
not exceed 55°C.
Install filler panel(s) in any empty slot(s) of the Mainframe.
Summary of Contents for Elgar ReFlex Power
