background image

 

iv 

 

Product Family: GUPS 2400A-107 

Warranty Period: One Year

 

WARRANTY TERMS 

AMETEK Programmable Power, Inc. (“AMETEK”), provides this written warranty covering the 
Product stated above, and if the Buyer discovers and notifies AMETEK in writing of any defect in 

material or workmanship within the applicable warranty period stated above, then AMETEK may, 
at its option: repair or replace the Product; or issue a credit note for the defective Product; or 

provide the Buyer with replacement parts for the Product. 

The Buyer will, at its expense, return the defective Product or parts thereof to AMETEK in 

accordance with the return procedure specified below. AMETEK will, at its expense, deliver the 
repaired or replaced Product or parts to the Buyer. Any warranty of AMETEK will not apply if the 
Buyer is in default under the Purchase Order Agreement or where the Product or any part 

thereof: 

 

is damaged by misuse, accident, negligence or failure to maintain the same as 

specified or required by AMETEK; 

 

is damaged by modifications, alterations or attachments thereto which are not 
authorized by AMETEK; 

 

is installed or operated contrary to the instructions of AMETEK; 

 

is opened, modified or disassembled in any way without AMETEK’s consent; or 

 

is used in combination with items, articles or materials not authorized by AMETEK. 

The Buyer may not assert any claim that the Products are not in conformity with any warranty 

until the Buyer has made all payments to AMETEK provided for in the Purchase Order Agreement.

 

PRODUCT RETURN PROCEDURE 

1.

 

Request a Return Material Authorization (RMA) number from the repair facility (

must be 

done in the country in which it was purchased

): 

 

In the USA

, contact the AMETEK Repair Department prior to the return of the 

product to AMETEK for repair: 
Telephone:  800-733-5427, ext. 2295 or ext. 2463 (toll free North America) 
 

858-450-0085, ext. 2295 or ext. 2463 (direct) 

 

Outside the United States

, contact the nearest Authorized Service Center 

(ASC).  A full listing can be found either through your local distributor or our 

website, www.programmablepower.com, by clicking Support and going to the 
Service Centers tab. 

2.

 

When requesting an RMA, have the following information ready: 

 

Model number 

 

Serial number 

 

Description of the problem  

NOTE:

  Unauthorized returns will not be accepted and will be returned at the shipper’s expense. 

NOTE:

  A returned product found upon inspection by AMETEK, to be in specification is subject to 

an evaluation fee and applicable freight charges.

 

Summary of Contents for GUPS 2400A-107





































Reviews: