Ametek Land LMG GS, User Manual

Design and Manufacturing Standards

Signs and Symbols Used on  

Equipment and Documentation

Caution, risk of electric shock.  

This item or material can be recycled.

Caution, attention to possibility of risk of damage to the product, 

process or surroundings. Refer to instruction manual.

Caution, hot surface.

This item or material can be recycled. 

This item or material must be disposed of in accordance 

with the Waste Electrical and Electronic Equipment 

directive as applied by local regulations.

Protective Conductor Terminal.

Observe precautions for handling electrostatic discharge 

sensitive devices.

IMPORTANT INFORMATION - PLEASE READ

Important Health and Safety Information

Equipment Operation 

Use of this instrument in a manner not specified by Land Instruments International may be hazardous.

Electrical Power Supply 

Before working on the electrical connections all of the electrical power lines to the equipment must be isolated. All the 

electrical cables and signal cables must be connected exactly as indicated in these operating instructions. If in doubt 

contact Land Instruments International.

Face and Eye Protection

Suitable face and eye protection must be worn when working on hot vessels and ducts! Special safety measures must be 

taken when working on a high-pressure duct.

Protective Clothing

Protective clothing must always be worn when working in the vicinity of hot vessels or ducts.

Storage

The instrument should be stored in its packaging, in a dry sheltered area.

Unpacking

Check all packages for external signs of damage. Check the contents against the packing note.

Return of Damaged Goods

IMPORTANT 

If any item has been damaged in transit, this should be reported to the carrier and to the supplier immediately. Damage 

caused in transit is the responsibility of the carrier not the supplier.

DO NOT RETURN a damaged instrument to the sender as the carrier will not then consider a claim. Save the packing with 

the damaged article for inspection by the carrier.

Return of Goods for Repair

If you need to return goods for repair please contact our Customer Service Department. They will be able to advise you on 

the correct returns procedure.

Any item returned to Land Instruments International should be adequately packaged to prevent damage during transit.

You must include a written report of the problem together with your own name and contact information, address, 

telephone number, email address etc.

Return of Goods for Repair Form is available for download from our websites.

Lifting Instructions

Where items are too heavy to be lifted manually, use suitably rated lifting equipment. Refer to the Technical Specification 

for weights. All lifting should be done as stated in local regulations.

Office Locations

UK - Dronfield

Tel: +44 (0) 1246 417691 

E-Mail: land.infrared@ametek.co.uk

Web: www.landinst.com

USA - Pittsburgh 

AMETEK Land, Inc. 

Tel: +1 412 826 4444

E-Mail: irsales@ametek.com

Web: www.ametek-land.com

For further details on all LAND/ 

Ametek offices, distributors and

representatives, please visit our

websites.

The Quality Management System of  

Land Instruments International is approved  

to BS EN ISO 9001 for the design, 

manufacture and on-site servicing of 

combustion, environmental monitoring and 

non-contact temperature measuring 

instrumentation.

        Approvals apply in the USA

   This instrument complies with current European directives relating to 

   Electromagnetic Compatibility 89/336/EEC and Low Voltage Directive  

   73/23/EEC.

Operation of radio transmitters, telephones or other electrical/electronic devices in 

close proximity to the equipment while the enclosure doors of the instrument or its 

peripherals are open, may cause interference and possible failure where the radiated 

emissions exceed the EMC directive.

The protection provided by both CE and IP classifications to this product may be 

invalidated if alterations or additions are made to the structural, electrical, mechanical 

or pneumatic parts of this system. Such changes may also invalidate the standard terms 

of warranty.

Dimensions

Unless otherwise stated, all measurements are given in millimetres and inches.

Copyright

This manual is provided as an aid to owners of Land Instruments International’s products 

and contains information proprietary to Land Instruments International. This manual may 

not, in whole or part, be copied, or reproduced without the expressed written consent 

of Land Instruments International Ltd.

Copyright © 2007 - 2010 Land Instruments International.