Installation
5
Section 2: Installation
2.1 Unpacking
Carefully remove the contents of the shipping carton and check
each item against the packing list before destroying any packing
material. If there is any shortage or damage, report it to the
factory immediately.
2.2
Mounting and Installation Guidelines
CAUTION:
The IntelliPoint RF instrument must be powered AFTER it
is installed in the application and with material BELOW the
sensing element.
The IntelliPoint RF instrument can be mounted vertically or
horizontally at any angle. The mounting location should be
as free as possible from vibration, corrosive atmospheres, and
any possibility of mechanical damage. Ambient temperatures
at electronics should be between limits as specified by control
drawings in section 6.
The IntelliPoint RF instrument uses a dual compartment
housing and a completely encapsulated input/output module
to reduce the possibility that damage may occur from water
migrating into the housing through the conduit. To further
reduce the possibility of damage caused by water in the conduit,
install a drip loop and breather drain to purge any accumulating
moisture.
Refer to Figure 2-1
.
Figure 2-1
Recommended Conduit Connection
Summary of Contents for SIL IntelliPoint RF S*R*L Series
