Installation
11
2.6.5
Manual / Remote Certify™
The "Certify" test feature performs a confidence test of the
system by duplicating the same signal as a high-level alarm
condition without requiring the system to be removed from the
tank. Simulating a high level with the Manual/Remote Certify
feature:
• Checks the AutoVerify™ and system circuits to ensure
proper operation.
• Checks the integrity of the wiring connections.
• Verifies that the sensing element is working properly.
The "Manual Certify" test is initiated with the press of the
Manual Certify Button located on the sensing element / circuit
side of the housing.
The "Remote Certify" test is initiated by creating a momentary
short between contacts 7 and 8 located on the power supply
side of the housing. This can be done with a push button or
relay closure.
After initializing the Certify test, the green LED flashes
for 5 seconds and the red LED will illuminate. The current
moves to the alarm condition for 2 seconds. If the red LED
does not turn on, and the current does not move to the alarm
condition, the Certify has detected a fault.
Consult Section
4: Troubleshooting
.
2.6.6 AutoVerify™
"AutoVerify" is a self-testing function that continuously checks
the system for proper operation when the unit is in the High
Level Failsafe (HLFS) mode and in normal condition.
The Safety IntelliPoint switch is shipped with AutoVerify
Enabled and tamper sealed.
AutoVerify Can Not be Disabled on the Safety IntelliPoint.
If a fault is detected during the AutoVerify cycle, both LEDs
will flash and the relays will de-energize.
Summary of Contents for SIL IntelliPoint RF S*R*L Series
