SXRXLXX1 - SIL IntelliPoint RF Series User's Manual
16
2.9 Calibration
The Intellipoint™ model RNT (Standard Sensitivity) and
RHT (High Sensitivity) feature Auto-Cal calibration. Auto-
Calibration is suitable for liquid and slurry applications.
2.9.1
Using the Intellipoint with Auto-Calibration
After the Intellipoint is installed in the vessel with material
below the sensing element, simply apply power. The Intellipoint
electronic unit will auto calibrate.
Caution – The material being measured must be below the
sensing element when power is applied (Sensing element
uncovered).
Calibration is complete.
If power has been applied to the IntelliPoint prior to installation
(on a test bench) or, if the Intellipoint is moved from one vessel
to another, RECAL is necessary for the unit to capture the new
air value.
After the IntelliPoint has been installed with the measured
material below the sensing element, press and hold the "ReCal"
button (shown in
Figure 2-4
) for five (5) seconds. After five
seconds, the two LED’s flash for sixty seconds before reset
occurs.
2.9.2
IntelliPoint Calibration Mode Change
The IntelliPoint was shipped in a calibration mode that was determined
to meet the needs of the application for which it was originally sold. If, for
some reason, the IntelliPoint is used on a different application, or for other
reasons it is determined that a different calibration mode should be used,
use the following procedure to make a calibration mode change.
A full system proof test must be performed when:
- Any system component is changed or replaced by the user.
- Any system component or setting is modified by the user.
Summary of Contents for SIL IntelliPoint RF S*R*L Series
