background image

8

Manual Part No. 502923 Issue 3

5.0:  Mechanical Installation

5.0: Mechanical Installation

5.4: Tip Adjustment 

The Mini Probe Tip height can be adjusted over a 

0.5 mm range (± 0.25 mm from the factory set position 

-approximately ±½ turn).

To adjust tip

1)  Firmly hold the Mini Probe frame as shown, so that it is 

not stressed during the tip adjustment

2)  Using the spanner supplied, turn the tip until the 

required tip extension is achieved..

5.5: Tip Replacement 

To remove tip

1)  Firmly hold the Mini Probe frame, so that it is not 

stressed during the tip removal.

2)  Using the spanner supplied, unscrew the tip from 

the Mini Probe.

To install tip

1)  Firmly hold the Mini Probe frame, so that it is not 

stressed during the tip installation.

2)  Using the spanner supplied, screw the 

replacement tip into the Mini Probe until the required 

tip extension is achieved. The tip is self-locking, so a 

tightening torque is not applicable. Do not tighten the 

tip against the stop.

CAUTION

 

In order to avoid damage to the probe, it is critical that the Mini Probe is held firmly whilst the tip is being 

adjusted. Failure to do so will stress the assembly and may damage the structure beyond repair.

Summary of Contents for Solartron Metrology Digital Mini Probe














Reviews: