background image

                                               

UPS + Isolation Transformer        User Manual 

    

© 2020 AMETEK Electronic Systems Protection | Technical Support: 1-800-645-9721 | surgex.com                                                                                                 

16

                                      

 

 

 

 

Reference the below UPS fault code chart to identify the status of the UPS.

 

 

UPS Status Code

 

Definition

 

IF

 

Inverter fault

 

BE

 

Back-Feed fault

 

HL

 

Unit is off due to a high line

 

LL

 

Unit is off due to a low line

 

DB

 

Unit is off due to a low battery

 

FF

 

Fan fault

 

SF

 

Site wiring fault

 

 

NOTE:

 

• 

 If the UPS is on continuously, it will perform an auto battery test every six days.

 

• 

 If you  are  utilizing MopUPS  Pro  software, you  can  configure  the  system to 

automatically self-test periodically.

 

• 

 The UPS is shipped with a charged battery, but some discharge naturally occurs 

during storage and shipment. You may use the UPS immediately, but you should 
realize that backup time may be less than the stated rating until the UPS battery has 
had at least six hours to charge.

 

• 

 SurgeX recommends that you do not plug laser printers into the UPS. Laser printers 

are known to draw large amounts of current when the fuser/heater assembly is 
energized. Laser printers can easily overload the UPS or create a low voltage 
condition that can interfere with the operation of the Voltage Manager circuit.

 

 

 

 

ON  

 

OF F  

1             2           3           4 

Summary of Contents for SurgeX UPS-1440-Li-ISO































Reviews: