AMH SL03528 Manual Download | Manualshive

Page: 11 / 20

background image

MAN-X5SL-ENG-01

11

ⓒ

2016 All Material Handling

10.0 TROUBLE SHOUTING

Trouble

Cause

Cure

Hand Wheel (33)
does not move in or
out

Selector not in neutral “N” position

Move Selector to neutral “N”

Hoist is loaded

Never attempt to pull hand wheel
out when the hoist is loaded.

Improper assembly

Requires service for repair

Free chain mode
does not allow chain
to be pulled freely

Chain pulled too fast or accelerated
too quickly causing the brake to set

Reset the hand wheel (33) and pull
load chain with less force

Assembly of outer brake spring (34)
may be preloaded in excess of 120º

Requires service for repair.

Hoist will not lift or
lower at no load

Brake is not set

See section 1.0 OPERATION in
this manual: instructions 5 and 6

Lever moves without clicking, chain
does not continue to move in or out

There must be some resistance to
cause the lever to ratchet. Hold or
pull the slack chain by hand while
ratcheting the lever. Or, use the
free chain mode to easily position
the chain.

Improper assembly of brake
components between the hand wheel
(33) and brake driver (22)

Requires service for repair.

Re-assemble components
between the hand wheel (33) and
brake driver (22) per instruction
and illustration in section 9.0
ASSEMBLY in this manual.

Hoist will not lift.
Slight clicking when
lever is rotated in up
direction

Brake disc (20) installed upside
down not allowing the pawls (17) to
engage.

Requires service for repair
improper brake disc installation.

Hoist will not lift.

No clicking when

lever is rotated in up
direction

Pawls (17) not engaging the brake
disc (20). Due to spring failure,
corrosion or contamination

Requires service for repair. Clean
and inspect pawl and spring for
proper function.

Up, Dn Selector is not indexed
correctly or spring (25) missing

Requires service for repair. Clean
and inspect parts and assure
proper assembly

Bottom hook (80) and slack end pull
handle (16) are assembled on the
wrong end of the chain.

Requires service for repair.

Looking at the lever end, the
bottom hook (80) should be on the
left side and the Pull handle (16)
on the right.,

Continued on next page

«
...
9
10
11
12
13
...
»

Summary of Contents for SL03528





















Reviews:

No comments

Related manuals for SL03528

Brand: Toku Pages: 37

Brand: Schmalz Pages: 46

Brand: YATO Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands