background image

 

- 35 -

 

AMIAD LIMITED WARRANTY  

This certificate applies to Amiad Products purchased by You from Amiad or an Amiad authorized Distributor (“Distributor”). This limited 
warranty extends only to the original purchaser, and is not transferable to anyone who subsequently purchases, leases, or otherwise 
obtains the Product from the original purchaser.  
1. 

Amiad hereby warrants that the Products are and will be free from defects in material and workmanship under normal use 
and service. Amiad warrants that it will correct manufacturing defects in the Products, in accordance with the conditions set 
out in this warranty. 

2. 

This warranty is enforceable for a period of 12 months after the date Bill of Lading or equivalent (the “Warranty Period”).  

3. 

In the event that during the Warranty Period the Distributor discovers a defect in material and/or workmanship in any 
Product or part (the “Defective Product”), it shall submit a written complaint to Amiad using Amiad's standard customer 
complaint form. For the receipt of the customer complaint form, the submission of the complaint or any questions please 
contact your customer service representative.  

4. 

Upon written demand by Amiad the Distributor shall return the Defective Products – or a sample thereof – to Amiad, at 
Amiad's cost. If the customer ships any such Product, Amiad suggests the customer package it securely and insure it for value, 
as Amiad assumes no liability for any loss or damage occurring during shipment. Provided however that in the event Amiad 
determines that the warranty does not apply to such Product, Distributor shall promptly reimburse Amiad for such cost 
(including freight and customs). Any returned Product or part must be accompanied by the warranty certificate and the 
purchase invoice. It is clarified that the Distributor may not return the Defective Product unless such return was coordinate 
and approved by Amiad in advance.   

5. 

Amiad's obligation under this warranty shall be limited to, at its option, the repair or exchange, free of charge, of the Product 
or any part which may prove defective under normal use and service during the Warranty Period. The provision of a repaired 
or replacement Product during the Warranty Period will result in an extension of the Warranty Period by an additional period 
of 12 months, provided that the total accumulated Warranty Period shall in any event be no more than 18 months from the 
original Bill of Lading.  

6. 

This warranty is valid on the condition that the Products are installed according to Amiad's instructions as expressed in 
Amiad's instruction manuals and according to the technical limitations as stipulated in Amiad's literature or as stated by a 
representative of Amiad.  

7. 

This warranty will not apply to damaged or defective Products resulting from or related to:  

(i) 

Fire, flood, power surges or failures or any other catastrophe/and or unforeseen occurrence, such as but not limited to those 
for which the customers are customarily insured;  

(ii) 

Fault, abuse or negligence of the customer;  

(iii) 

Customer's responsibilities, including the failure of the intake water to meet the agreed standards, as set forth in a written 
document, approved by Amiad or improper storage.  

(iv) 

Improper or unauthorized use of the Product or related parts by the customer, including the customer’s failure to operate the 
Product in conformity with the recommendations and instructions of Amiad, as set forth in Amiad's manuals and other 
written materials, the operation of the Product other than by a trained and qualified operator, or improper installation of the 
Product by a third party not authorized by Amiad;  

(v) 

Performance by the customer of maintenance and other services other than by a trained and qualified advanced operator, or 
other than in conformity with the recommendations and instructions of Amiad, or other than in accordance with procedures 
defined in the literature supplied for Products;  

(vi) 

Any alteration, modification foreign attachment to or repair of the Products, other than by Amiad or its authorized technical 
representatives.  

8. 

In no event shall Amiad be liable to the customer or any third party for any damages, including indirect, special, exemplary, 
punitive or consequential damages, or lost profits arising out of or in connection with this warranty, or arising out of or in 
connection with the Product's performance or failure to perform, even if it has been advised of the possibility of such 
damages.  

9. 

Amiad will be excused for failure to perform or for delay in performance hereunder if such failure or delay is due to causes 
beyond its reasonable control or force majeure preventing or hindering performance. 

10. 

The limited warranty set forth herein is the only warranty given by Amiad and is provided in lieu of any other warranties 
created by any documentation, packaging or otherwise.  

11. 

Amiad makes no warranty whatsoever in respect of accessories or parts not supplied by Amiad. In the event that Amiad is 
required  to  correct  a  defective  Product  or  product  not  covered  by  this  warranty,  it  will  do  so  solely  in  consideration  for 
additional fees. 

Summary of Contents for AMF2-93K




































Reviews: