background image

Maintenance

Operate shutoff valves periodically and repair them, if seals tend to stick or leak. Notify all concerned 

personnel before shutting off any gas supply.

WARNING: To protect the lives of patients, always notify the appropriate medical facility staff before 

shutting off the supply of medical gas or vacuum through a shutoff valve. Do not close shutoff valves 

except in cases of emergency or maintenance.

Clean the exterior of the valve boxes routinely with soap and water. Strong solvents may damage the Lexan 

window.

Authorized hospital personnel should close shutoff valves in the event of fire, explosion or damage to the 

pipeline systems or equipment.

In Alarm Valve Combo Unit boxes, the Shutoff Valve handles become accessible after the window has been 

removed from the valve box.

To remove the window, grasp the ring and pull outwards. Turn valve handle towards you to shut off the 

flow of gas or vacuum.

Zone Valves have a swingout design body which makes changing the internal components of the ball 

valve easier.

All valve bodies can be accessed by loosening all bolts and nuts and removing only one bolt, at this point the 

valve body can be swung out for servicing. 

For Annual Test

•  Reset power to make sure all LED's light up

•  Push and hold the “Test” button to light up all LED’s and audible alarm

  

   

www.amico.com 

   

 7

Summary of Contents for Alarm Valve Combo Unit

































Reviews: