Remote control receiver & keyfob upgrade kit type AP433RX2 Programming Procedure
Keyfob Transmitter Programming
Your key-fob transmitters(s) will be
pre-programmed to your AP433RX2
receiver unit ready for use with the
buttons assigned as follows:
button 1 assigned to Channel 1
button 2 assigned to Channel 2
If any further transmitters are added
these will require programming to the
receiver by one of the following methods:
(A) Remote Programming Method
(requires an existing pre-programmed keyfob)
1. Take a transmitter that has already been programmed
to the AP433RX2 receiver and press & hold the active button
and release after 10 seconds.
2
. Press the transmitter button you would like to assign
to the receiver.
3.
The receiver should now respond each time you
press the transmitter button you’ve just assigned.
(B) Alternative Programming Method
(use this method
if you don’t have an existing pre-programmed keyfob)
Open the receiver cover and locate the red ‘
SEL
’ button inside
1. Briefly press the ‘
SEL
’ button once and release, the red
CH1
LED on the receiver will flash red to indicate that the
AP433RX2 receiver is ready to learn the transmitter code.
2
. Whilst the CH1 LED is flashing, press the transmitter
button you would like to assign to the receiver and the
red LED will stop flashing.
3.
The receiver should now respond each time
you press the button you’ve just assigned.
Note: If you are connecting the AP433RX2 to two doors
press the ‘SEL’ button twice to programme channel 2
for the second door, the
CH2 LED
will start flashing,
then follow steps 2 & 3 above to assign a separate
transmitter button to the other door.
Repeat the above procedure to assign
additional keyfob transmitters to the
AP433RX2 receiver. (multiple buttons on
each keyfob may be assigned if desired)
Clearing the receiver memory
(necessary if a key-fob has been lost or stolen)
This will erase all previously stored
keyfobs from the receiver memory
1.
Press and hold the ‘
SEL
’ button on
the receiver unit for five seconds.
2.
After 5 seconds both red LED’s will flash 3 times to
confirm that the receiver memory has been cleared.
3.
Release the ‘SEL’ button. You may confirm that all the
previously stored keyfobs have been deleted by pressing the
transmitter buttons previously used to operate the door/gate.
There should be no response.
Follow programming method (B) above
to re-learn your keyfobs
Transmitter Battery Replacement
(AP433TX4 keyfob)
When the AP433TX4 keyfob battery is low the red LED will flash
rapidly when a button is pressed. Remove the three screws
from rear of the keyfob and remove the casing to reveal a
12 volt battery type GP27A (or LR27A)
Troubleshooting Guide
If your system is not working properly please
perform the following troubleshooting checks:
1. Does the red LED on the AP433TX4 transmitter
illuminate when a button is pressed?
a. Solid red LED = battery OK, proceed to step 2.
b. Rapid flashing LED = battery requires replacement.
c. No LED, try a new battery and make sure that it is
installed correctly. If the LED fails to illuminate after
changing the battery replace the transmitter.
2. Open the AP433RX2 receiver cover
and check that the
two red LED’s are illuminated inside the receiver unit. If not,
ensure that the receiver is connected to a power source.
The transmitter must be programmed to the receiver
before proceeding with the following troubleshooting steps.
(see programming procedure opposite)
3. When the transmitter button is pressed, can a ‘click’
sound be heard from the AP433RX2 receiver unit?
• If yes, the transmitter and receiver are working properly
but there is another issue, proceed to step 5.
• If no, the receiver is not recognising a signal from the
transmitter.
4. If the receiver is not responding to a signal
from the transmitter consider the following:
Door operator motors and controls may cause radio
frequency interference (RFI) that could impair the performance
of a radio control device. Materials such as metal, electrical
cables, or other electronic devices may affect the signal.
For best results, locate the receiver away from the motor.
• Try holding the transmitter near the receiver and activate it.
If the receiver responds to the signal try moving the receiver
to a new location away from metal items & other wires etc.
• Try activating the receiver with a different transmitter. If the
receiver responds to a different transmitter, there is a possibility
that the original transmitter has a problem. If this occurs, follow
programming procedure (b) to re-learn the suspect transmitter to
the receiver unit and try replacing the battery
• Do not cut or lengthen the antenna wire.
• If the receiver is not responding to the signal from any
transmitter, regardless of distance, it is possible that the receiver
may be faulty and require replacement, in which case contact
Amourelle Products Ltd for assistance.
5. If the receiver and transmitter are functioning correctly
but not activating the door or gate, ensure that the output
wires from the receiver are connected properly to the door
control circuit and check the operation of the motor etc.
from the wired-in wall mounted pushbutton switch, if fitted.
(if no pushbutton switch is installed you’ll need to locate the low
voltage wall control pushbutton switch terminals and briefly short
the terminals together with a metal object, this should start the
motor and operate to door) If you are unable to locate the low
voltage wall control pushbutton switch terminals, please refer to
the owners manual supplied with your electric door operator.
Note:
Amourelle Products Limited reserves the right to make
any alterations deemed appropriate for the technical
improvement of the product at any time, whilst leaving its
essential features unchanged.
Amourelle Products
, Unit 16 James Scott Rd, Halesowen,
West Midlands B63 2QT - Phone: 01384 900 264
AP433TX4
button assignment
