AMP Lighting BeaconPro Path & Area Light Installation & Maintenance Manual Download

Page: 5 / 8

customersupport@amplighting.com • 813.978.3900

–5–

INSTALLATION & MAINTENANCE GUIDE

AMP

BeaconPro Path & Area Light

APL-3030-4-B-BZ

Reinstall Hat Bottom

Reinstall the hat bottom using

the previously removed screws.

Use a screwdriver to make sure

the screws are secure.

Hat Top

Hat Bottom

Screw

Remove Lens

Remove the lens on the bot-

tom of the hat by loosening the

screws using a screwdriver.

Lens

Hat

Screw

Use SCB lamp with correct wattage

and type marked on fixture label.

Align the bayonet base of the SCB

lamp to bayonet socket. Insert the

SCB lamp into the bayonet socket and

twist it until the SCB lamp is inserted

properly.

CAUTION: Do not exceed

maximum wattage marked on lumi-

naire label.

SCB Lamp

Bayonet Socket

Install SCB Lamp

Summary of Contents for BeaconPro Path & Area Light









Search results

Summary of Contents for BeaconPro Path & Area Light

Reviews:

Related manuals for BeaconPro Path & Area Light

Brands by name

Popular brands

AMP Lighting BeaconPro Path & Area Light, Installation & Maintenance Manual

Search results

Summary of Contents for BeaconPro Path & Area Light

Reviews:

Related manuals for BeaconPro Path & Area Light

Brands by name

Popular brands