20
Once the above mentioned data are all entered,
the program needs to know the values
corresponding to the inserting positions and
the number of V-nails that have to be driven
for each position (max.9).
Two possibilities are available:
1. self-learning mode (F5) see chapt. 5.4.11.a
2. insertion mode. see chapt.5.4.11.b
5.4.11.a F5 Self-learning
Pressing F5 , the following picture is displayed
on the screen:
use the yellow arrows <== ==>to move the V-nail
driver to the desired point, and check the
value on the bottom of the screen;
press ENTER when you reach the desired position;
on the table below in the frame picture the
chosen value is shown and the user is prompted
to digit the number of V-nails he wants to
insert in that point:
press F5 again to program possible new positions,
then repeat the above mentioned procedure, or
press the MENU key to exit and save.
NOTE: When the V-nail driver is positioning, F1
can be used instead of ENTER to confirm, otherwise
press F2 to cancel.
5.4.11.b Insertion
Use the yellow arrows to move to the position 1 of the
inserting point management:
Type the value in mm of the distance from the
external vertex of the mouldings to be assembled
- then press ENTER;
the cursor shifts on the V-nail number programming side:
type the amount of V-nails you wish to insert in the just
defined position (max. nine V-nails per position) then
press ENTER;
The cursor will position automatically on the next value:
repeat the above mentioned steps to add further insertion
points.
To switch back to the program list press the
MENU key. Press MENU again to return to the
main menu.
If one of the critical data to run the cycle is
missing a message appears on the screen asking
the user to either enter the missing data or
terminate the program definition, in which case
the program will be considered as incomplete.
The F1 ÷ F6 keys are enabled to perform the
following functions:
F1
Specifies the height of V-nails to be used
in the program
F2
Specifies the sharpening of V-nails to be
used in the program
F3
Specifies the hardness of material to be
used in the program
F4
Specifies the width of the moulding, (not including
the rabbit) in mm .
F5
Position self-learning
F6
Definition of running speed to be used in
the program
•
Press F1, the cursor blinks on the V-nail height field:
Type the height of the v-nails in mm;
•
Press F2, the cursor blinks on the V-nail sharpening field:
type the sharpening to be used (SW, MW etc.);
•
Press F3: the screen is updated and the following table
is displayed:
Use the yellow arrows to move along the table and, once the
type of material is selected, press ENTER.
•
Press F4, the cursor blinks on the frame profile width:
type in the size in mm then press ENTER.
*
Press F6, the following table is displayed on the screen:
Use the arrows to move along the table and , once the running
speed is selected, press ENTER or F1 to confirm it or F2 to
delete it & use the default value.
Codice Materiali
>
1
> Very Soft
2 Soft
3 Medium
4 Hard
5 Very Hard
6 Plastic
Codice Speed
>
1 > Speed slow 001
2 Speed slow 002
3 Speed normal 001
4 Speed normal 002
5 Speed fast 001
6 Speed fast 002
7 Speed extra fast 001
8 Speed extra fast 002
The working speed value will go to the default if
you decide not to change it. See default parameters
in chapt. 5.4.15.a
Summary of Contents for Mitre-Mite VN4 MemoryProgram
