L0126J
17
5
TRAY ADJUSTMENT AND CONFIGURATION
The trays in AMS Sensit 3 vendors are highly configurable.
Practically any combination of wide and narrow columns can be
set up on a tray. Before changing the configuration of your trays,
make sure to order the parts you will need, such as new helices,
dividers or additional motors.
SNACK, CANDY AND FOOD TRAYS
Removal
1. To remove the tray, gently pull forward until it
contacts one or more of the restraint tabs on the
side of the right rail mount. Press the tab(s) in
while pulling out on the tray slightly. Reposition
your hands to grasp the tray at its sides and slide
the tray out. If the tray is spaced close to the tray
above, it may be helpful to raise the front of the
tray as you pull it free.
2. When removing a tray, it is not necessary to
disconnect the tray harness. The harness is long
enough that it will allow a removed tray to be
placed on the floor without having to be
disconnected.
Installation
To install the tray, place the tray on top of the rails and
slide the tray all the way to the rear. It will automatically
drop into position. Make sure the harness slack is
draped over the outside of the rail.
BOTTLE TRAY
Removal
1. Disconnect the harness inside the right column in
the cabinet. The connections are labeled
corresponding to the number of the tray (1-7).
Push the connector out through the hole in the
back of the column.
2. Pull the tray out until it stops. Carefully pull the
harness up on top of the tray.
3. Locate the slide rail release levers on both sides of
the tray. There should be an arrow indicating which
way to push to release the levers. Note that the
lever direction on the right side is opposite the
direction on the left side. Push the release levers in
the directions indicated and simultaneously pull on
the tray.
4. Be sure to push the extended slide rails back into
the cabinet before closing the door. Otherwise the
slides will be damaged.
Installation
CAUTION:
An incorrectly installed tray can
disengage from the rails and fall when
extended! It is recommended that
installation be performed by two people!
1. Fully extend the slide rails in the cabinet and hold
in position.
2. Move the ball carriers out to the ends of the slide
rails (Refer to
Figure 5.1
below) and hold in
position.
3. Align the rails on the sides of the tray with the
extended slide rails and insert. Continue to hold
the ball carriers and slide rails in place until the
rails on the tray are firmly engaged in the ball
carriers.
4. Push the tray in completely to lock the rails
together.
5. Carefully extend the tray to check for proper
installation. Support the tray to prevent falling if the
rails are not properly engaged. Visually inspect the
rails, and gently pull the front of the tray side to
side to make sure the rails will not disengage.
6. Route the tray harness over the rail in the cabinet
and into the right column. Connect the tray harness
to the appropriate receptacle.
Figure 5.1 Bottle Tray Rails
Summary of Contents for 28 Slim Gem
