manualshive.com logo in svg

AMS EPIC SENSIT 3, Operation And Service Manual

The AMS EPIC SENSIT 3 is an innovative device equipped with cutting-edge technology for precision measurements. This Operation And Service Manual is essential for users to understand the product's features and optimize its performance. To access the comprehensive manual, visit our website and download it for free to unlock the full potential of the AMS EPIC SENSIT 3.

Share
Download
background image

L0190D

 

 

41

 

10

 

SUPPORTED

 

DEX

 

FIELDS

 

NOTE: Certain fields may not be reported if the value is zero. 

BA101   Bill Validator Serial Number  
BA102   Bill Validator Model Number  
BA103   Bill Validator Software Revision  

 

CA101   Coin changer serial number  
CA102   Coin changer model number  
CA103   Coin changer software revision 
  
CA201   Value of cash sales since initialization  
CA202   Number of cash vends since initialization  
CA203   Value of cash sales since last reset  
CA204   Number of cash vends since last reset  
 
CA301   Value of cash in since last reset  
CA302   Value of cash to the cash box since last reset  
CA303   Value of cash to tubes since last reset  
CA304   Value of bills in since last reset  
CA305   Value of cash in since initialization  
CA306   Value of cash to the cash box since initialization  
CA307   Value of cash to the tubes since initialization  
CA308   Value of bills in since initialization  
CA309   Value of bills in since last reset    (DEX 6.0 Format) 
CA310   Value of bills in since initialization   (DEX 6.0 Format) 
 
CA401   Value of cash dispensed since last reset  
CA402   Value of cash manually dispensed since last reset  
CA403   Value of cash dispensed since initialization  
CA404   Value of cash manually dispensed since initialization 
  
CA601   Number of DEX reads performed since initialization  
CA602   Number of door openings since initialization  
 
CA701   Value of cash discounts since last reset  
CA702   Value of cash discounts since initialization  
CA703   Number of cash discounts since last reset  
CA704   Number of cash discounts since initialization  
 
CA801   Value of cash overpay since last reset  
CA802   Value of cash overpay since initialization  
 
CA1001  Value of cash filled since last reset  
CA1002 Value of cash filled since initialization  
CA1501 Value of coin tube contents (as reported by the mech) 
CA1701 Coin type in payout tube (per MDB spec)  
CA1702 Coin value in payout tube (per MDB spec) 
CA1703 Number of coins in payout tube (as tracked by VMC) 
CA1706 Tube Full (1 if Yes, not sent if No) 
 
CB101   Control board serial number  
CB102   Control board model number  
CB103   Control board software revision  
 

DA101   Cashless 1 Serial Number  
DA102   Cashless 1 Model Number  
DA103   Cashless 1 Software Revision  
 
DA201   Value of cashless 1 sales since initialization  
DA202   Number of cashless 1 vends since initialization  
DA203   Value of cashless 1 sales since last reset  
DA204   Number of cashless 1 vends since last reset  
 
DA401   Value credited to cashless 1 device since initialization  
DA402   Value credited to cashless 1 device since last reset 
  
DA501   Value of cashless 1 discounts since last reset  
DA502   Number of cashless 1 discounts since last reset  
DA503   Value of cashless 1 discounts since initialization  
DA504   Number of cashless 1 discounts since initialization  
DA505   Value of cashless 1 surcharges since last reset  
DA506   Number of cashless 1 surcharges since last reset  
DA507   Value of cashless 1 surcharges since initialization  
DA508   Number of cashless 1 surcharges since initialization 
 
DA901   Value of cashless overpay since last reset  
DA902   Value of cashless overpay since initialization  
 
DB101   Cashless 2 Serial Number  
DB102   Cashless 2 Model Number  
DB103   Cashless 2 Software Revision  
 
DB201   Value of cashless 2 sales since initialization  
DB202   Number of cashless 2 vends since initialization  
DB203   Value of cashless 2 sales since last reset  
DB204   Number of cashless 2 vends since last reset  
 
DB401   Value credited to cashless 2 device since initialization  
DB402   Value credited to cashless 2 device since last reset 
  
DB501   Value of cashless 2 discounts since last reset  
DB502   Number of cashless 2 discounts since last reset  
DB503   Value of cashless 2 discounts since initialization  
DB504   Number of cashless 2 discounts since initialization  
DB505   Value of cashless 2 surcharges since last reset  
DB506   Number of cashless 2 surcharges since last reset  
DB507   Value of cashless 2 surcharges since initialization  
DB508   Number of cashless 2 surcharges since initialization 
 
DXE01   Transmission Control Number: “1”  
DXE02   Number of Included Sets: “1”  
 
EA101

1

  Event Identification* 

EA102

1

  Date of Event (yymmdd – local date)  

EA103

1

  Time of Event (“hhmm”-DEX 5.0, “hhmmss” DEX 6.0) 

 

Summary of Contents for EPIC SENSIT 3





















































Reviews:

No comments

Related manuals for EPIC SENSIT 3

Janome Memory Craft 9450QCP Instruction Book preview
Memory Craft 9450QCP
Brand: Janome Pages: 124
Sagem Phonefax 35DS User Manual preview
Phonefax 35DS
Brand: Sagem Pages: 48
Quasar Autopax PAX405 User Manual preview
Autopax PAX405
Brand: Quasar Pages: 124
W6 WERTARBEIT N 656D Free Arm Manual preview
WERTARBEIT N 656D Free Arm
Brand: W6 Pages: 102
Zhejiang Sansilou Industrial BECS-129S Manual preview
BECS-129S
Brand: Zhejiang Sansilou Industrial Pages: 112
GBC C210 Instruction Manual preview
C210
Brand: GBC Pages: 38
Garudan GF-1130-4412 MH User Manual preview
GF-1130-4412 MH
Brand: Garudan Pages: 71
Baumfolder BAUM 2018 Instruction Manual preview
BAUM 2018
Brand: Baumfolder Pages: 50
UnionSpecial 3000 Instructions And Illustrated Parts List preview
3000
Brand: UnionSpecial Pages: 24
Medion MD 17187 User Manual preview
MD 17187
Brand: Medion Pages: 129
Galaxy PH40V Instruction Manual preview
PH40V
Brand: Galaxy Pages: 28
RS Barcelona RS MAX User Manual preview
RS MAX
Brand: RS Barcelona Pages: 14
Baohui IGS Speed rider 3DX User Manual preview
IGS Speed rider 3DX
Brand: Baohui Pages: 100
TSE PTV100/72 Owner'S Manual preview
PTV100/72
Brand: TSE Pages: 480
Singer Touch & Sew 600 Instruciton For Use preview
Touch & Sew 600
Brand: Singer Pages: 56
TAJIMA TCMX 601 User Manual preview
TCMX 601
Brand: TAJIMA Pages: 130
Barron Games X-Putt Operator'S Manual preview
X-Putt
Brand: Barron Games Pages: 24
Murata M-1600 Operating Instructions Manual preview
M-1600
Brand: Murata Pages: 34

Brands by name

Popular brands

Load more brands