AMSAN AM-TPL10F Manual Download

Page: 24 / 30

Two Post Car Lift AM-TPL10F

TROUBLE SHOOTING

Problem

Reason

Solution

Motor does not
work

•

Incorrect Voltage to motor

•

Motor burned out

•

Fuses are blown

•

Start Button damaged

•

Limit or Micro switch

burned out

•

Check the power fuse and

reset breaker

•

See if power unit wired

correctly

•

Avoid extension cords

•

Double check the installation

manual if any step got missed

Lift does not
raise

•

Incorrect voltage to power

unit

•

Internal leak to cylinder

and lowering valve

•

Motor damaged

•

Oil has air in it

•

Dirty oil

•

Hydraulic leak

•

Load exceeds the

capacity of the lift

•

Replace dirty oil and use

Dexron ATF

•

Check oil level if low top it up to

the correct level

•

See installation manual for

bleed cylinders

•

Double check the voltage and

wiring

•

Replace Damaged motor

•

Thorough inspect lift for

leakage and fix them

•

Double check the load

Capacity and make sure

it’s

below the rated capacity for the
vehicle lift

Lift does not
stay up

•

Oil has air in it

•

Internal leak to cylinder

and lowering valve

•

Motor damaged

•

Fitting leaks

•

Check oil level if low top it up to

the correct level

•

See installation manual for

bleed cylinders

•

Replace Damaged motor

Loud noise
coming from
the Lift while
raising/loweri
ng the load

•

The sliding and rotational

part missing lubrication

•

Damaged Sliders or

Sliders missing lubrication

•

Add lubrication to sliders and

other rotational parts

•

Replace Sliders

Power Unit
make noise
and does not
work.

•

Capacitor is damaged.

•

The voltage is too low.

•

The equipment is used

overload.

•

Replace the Capacitor

•

Have an electrician check the

low voltage issue

Motor

has

insufficient
pressure

raise the lift

•

Hydraulic leak

•

Load exceeds the

capacity of the lift

•

Low Fluid level

•

Remove the leak

•

Double check the load

Capacity and make sure its
below the rated capacity for the

Summary of Contents for AM-TPL10F































Search results

Summary of Contents for AM-TPL10F

Reviews:

Related manuals for AM-TPL10F

Brands by name

Popular brands

AMSAN AM-TPL10F, Manual

Search results

Summary of Contents for AM-TPL10F

Reviews:

Related manuals for AM-TPL10F

Brands by name

Popular brands