Installing Wall-Mount (MXD) Panels
55
Modero X® Series G4 Touch Panels Instruction Manual
Wiring a 12VDC Power Connection
To use the 2-pin 3.5 mm captive wire connector with a 12 VDC-compliant power supply, the incoming PWR and GND
wires from the external source must be connected to their corresponding locations on the connector (FIG. 34). The
connector uses locking screws to insure a connection to the device, so make sure to insert and tighten the screws before
applying power.
1.
Insert the PWR and GND wires on the terminal end of the 2-pin 3.5 mm captive wire cable.
Match the wiring locations of the +/- on both the power supply and the terminal connector.
2.
Tighten the clamp to secure the two wires.
Do not tighten the screws excessively; doing so may strip the threads and damage the connector.
3.
Verify the connection of the 2-pin 3.5 mm captive wire to the external 12 VDC-compliant power supply and apply
power.
Uninstalling the MXD-2000XL-PAN / MXT-1900L-PAN
The MXD-2000XL-PAN and MXD-1900L-PAN are secured to the Backbox via screws. In certain circumstances, such
as firmware updates or other maintenance that requires accessing the device’s USB or Micro-USB ports, the panel may
need to be removed from the Backbox.
The side covers must be removed to access the screws that secure the panel to the Backbox.
Removing the Panel From Its Backbox
1.
The MXD-2000XL-PAN and MXD-1900L-PAN have removable side covers on the left and right (landscape) or top
and bottom (portrait) (FIG. 35).
Note that FIG. 35 shows the MXD-1900L-PAN, but the illustration applies equally to the MXD-2000XL-PAN.
Also note that FIG. 35 shows a landscape panel but the installation of a portrait panel is essentially the same, other
than the vertical orientation. :
2.
For each of the two side covers - insert a flat-head screwdriver (or similar tool) into the removal notches, and
carefully prey each side of the side cover free from the molding.
3.
Once the side covers have been removed, the screws securing the panel to the Backbox are accessible.
4.
Remove the screws on each side to free the panel from the Backbox.
5.
Grasp the bottom of the panel (Landscape) or right side (Portrait) and pull gently outward until the side of the panel
is free of the Backbox. Use your other hand to hold stable the front of the panel.
FIG. 34
NetLinx power connector wiring diagram
FIG. 35
MXD-1900L-PAN Side Covers (highlighted in blue)
PWR +
GND -
To the Touch Panel
Power Supply
Removal notch
Removal notch
Side Covers
Removal notch
Removal notch
Always pull on the frame of the touch panel. NEVER pull on the glass edge.
Summary of Contents for MXD-430
