47
Audio/Video Configuration
Using the WebConsole, you can create a group of several different audio inputs and outputs and collectively adjust specific set-
tings for the entire group. The following table lists the audio group options available on the on-screen menu.
Selecting an Audio Test Tone
Selecting a test tone for your input source can help determine if you have your audio devices connected correctly.
Perform these steps to select a test tone:
1. Press the
MENU ON/OFF
button on the front panel of the presentation system to open the On-Screen menu.
2. With
AUDIO
highlighted, press the right navigational button to view the audio options.
3. Press the down navigational button to select the audio device you want, then press the right navigational button to
view its options.
4. Press the down navigational button to select
OUTPUTS
, then press the right navigational button to view its options.
5. Press the down navigational button to highlight the
Test Tone Generator
option.
6. Press the
SELECT
button on the front panel and use the left and right navigational buttons to scroll through the
available test tones. Press
SELECT
again when you see the test tone you want.
7. Press the up navigational button to highlight the
Test Tone Enable
option.
8. Press the
SELECT
button on the front panel and use the left and right navigational buttons to enable the test tone.
Changing the Microphone Mode
Perform these steps to change the microphone mode:
1. Press the
MENU ON/OFF
button on the front panel of the device.
2. With the Audio Settings highlighted, press the right arrow button one time to access the Audio settings menu.
3. Press the down arrow button until the Microphone option is highlighted, then press the right arrow button to access
the Microphone options.
4. With Mic Mode selected, press the SELECT button and use the left and right arrow buttons to toggle between Single Stereo and
Dual Mono microphones.
5. Press the SELECT button to accept the option you want.
Instruction Manual - Incite Digital Video Presentation Systems
Audio Settings - Outputs Menu Options (Cont.)
Test Tone Gener ator
Use the left and right navigational buttons to select a test tone for the selected audio output. You can choose from Off,
60Hz, 250Hz, 400Hz, 1kHz, 3kHz, 5kHz, 10kHz, Pink Noise, and White Noise.
Audio Group
Displays the audio group this to which the amplifier belongs.
Audio Settings - Groups Menu Options
Mix
The options below appear when you press the right navigation button while this option is highlighted.
Input
Use the left and right navigational buttons to adjust the mix level of the audio input for the audio group. You can set the
level from 0 to -100.
Microphone 1
Use the left and right navigational buttons to adjust the mix level of microphone 1 for the audio group. You can set the
level from 0 to -100.
Microphone 2
Use the left and right navigational buttons to adjust the mix level of microphone 2 for the audio group. You can set the
level from 0 to -100.
Format
Use the left and right navigational buttons to change the audio format of the selected audio input. You can set the audio
format to Stereo or Mono. The default setting is Stereo.
Stereo Output Options
The options below appear when you press the right navigation button while this option is highlighted.
Mute
Use the left and right navigational buttons to mute the audio on all devices in the group.
Volume
Use the left and right navigational buttons to adjust the volume levels for all devices in the group.
Balance
Use the left and right navigational buttons to adjust the balance level of the selected audio output. You can set the
balance level from -20 to +20. The default value is 0.
Sync Delay
Use the left and right navigational buttons to set the number of milliseconds to delay the audio. You can set the delay
between 0 to 200 milliseconds. The default value is 32.
Mono Output Options
The options below appear when you press the right navigation button while this option is highlighted.
Mute
Use the left and right navigational buttons to mute the audio on all devices in the group.
Volume
Use the left and right navigational buttons to adjust the volume levels for all devices in the group.
Adv. Sup. Feedback
Use the left and right navigational buttons to enable or disable Advanced Suppression Feedback for the audio group.
