background image

AMYPOWER ALLTRACK R3 & R SERIES - Owner’s Manual (Rev. A)

 

 

8

 
 

  PROHIBITED - F. CHANGES & ADJUSTMENTS 

Never use non-Amypower parts to replace Amypower 
provided parts or make changes to your chair unless 
authorized by Amypower. (Doing so will void the 
warranty and may create a safety hazard.) 
 

  WARNING 

Accessories designed by manufacturers other than 
Amypower is not available through Amypower the order 
process have not been tested or approved for use by 
Amypower. 

1.  If you modify or adjust this chair it may increase the 

risk of a fall or tip-over. 

2. Modifications unauthorized by Amypower constitute 

remanufacturing of the wheelchair. This voids the 
warranty. The user then assumes all future liability for the 
wheelchair. 

 

  WARNING - G. WHEN SEATED IN A PARKED 

WHEELCHAIR 

1. Always turn off all power to your chair when you 
are parked, even for a moment. This will prevent: 

  Accidental movement from contact with the joystick 

by you or others. 

  Unintended brake release or movement from 

EMI sources. (See Section V) 
2. Make sure that persons who help you (for example, 
store clerks) are aware of the joystick and do not touch 
it. If they 
do, your chair may move suddenly when you do not 
expect it. 
 

  WARNING - H. ENVIRONMENTAL CONDITIONS 

Your chair is not designed for use in a heavy 
rain storm, or in snowy or icy conditions. 
1. Contact with water or excessive moisture can cause 
an electrical malfunction. The frame, motors and other 
chair parts are not water-tight and may rust or corrode 
from the inside. 
To avoid a chair failure: 

  Minimize exposure of your chair to rain or very wet 

conditions. 

  Never take your chair into a shower, tub, pool or sauna. 

  Do not use your chair in fresh or salt water (such 

as at the edge of a stream, lake, or ocean). 

 Make 

sure 

battery cover is secure. 

  Replace joystick boot if it becomes torn or cracked. 

  Make sure all electrical connections are secure. 

  Dry the chair as soon as you can if it gets wet, or if 

you use water to clean it. 
 
2. Proceed slowly and use extra care if you must 
operate your chair on a wet or slick surface. 

  When in doubt, have someone help you. 

  Do so only if you are sure it is safe. 

  Stop if one or both main wheels lose traction. If 

this occurs, you may lose control of your chair or 
fall. 
 

  Never operate your chair on a slope or ramp if there is 

snow, ice, water or an oil film present. 

 

 

  WARNING 

Extra caution should be used when employing the disc 
switch or the proximity head array as control devices. 
These two devices are susceptible to malfunction when 
wet. 
 

  WARNING - I. TERRAIN 

 

1.  This chair will perform at optimum on firm, even 

surfaces such as concrete, asphalt and indoor flooring. 

2.  Although equipped with suspension, the performance can 

be substantially reduced on uneven surfaces and rough 
terrain. 

3. Do not operate the chair on sand, loose gravel or 

soil. Doing so may damage wheels, bearings, axles, 
motors or loosen fasteners. 
 

  WARNING - J. STREET USE 

 

In most provinces, power chairs are not legal for use on 

public roads. Be alert to the danger of motor vehicles on 
roads or in parking lots. 

1.  Do not operate this wheelchair on any roadways 

that do not allow non-motor vehicle traffic. 

2. When visibility is limited by either darkness or 

weather conditions, do not operate the chair on any 
roadways. 

3.  It may be hard for drivers to see you. Make eye contact 

with drivers before you proceed. When in doubt, yield until 
you are sure it is safe. 
 

  WARNING - K. MOTOR VEHICLE SAFETY 

 
Your chair has been manufactured with built-in 

Transport Brackets only. 

These transport brackets have not been crash-

tested in accordance with WC-1 9. Use these 
transport brackets only to secure an unoccupied 
wheelchair during transport 

1.  NEVER let anyone sit in this chair while in a moving 
vehicle. 
2.  NEVER transport this chair in the front seat of a 
vehicle. It may shift and interfere with the driver 
3.  ALWAYS secure this chair so that it cannot roll or shift. 
4.  Do not use any chair that has been involved in 

a motor vehicle accident 

Summary of Contents for Alltrack R































Reviews: